Epson C11C640001 - LX 300+II B/W Dot-matrix Printer Скачать руководство пользователя

Страница: 73 / 129

Using the Control Panel

2. Hold down the

Tear Off

(

Font

) button and then turn on the

printer.

The printer enters Default Setting mode and prints
instructions for selecting the language. The current language
is indicated by which control panel lights are on. (For
English, only the Pause light is on.)

3. If you want a different language, press the

LF/FF

button until

the lights show the language you want.

4. Press the

Tear Off (Font)

button to print a list of all the

current settings.

5. If the settings are all correct, turn off the printer to exit

Default Setting mode.

If you want to change any settings, go to step 6.

6. Press the

Tear Off (Font)

button. The printer prints

instructions for changing the settings.

7. Press the

LF/FF

button to scroll through the options for the

selected setting until you see the one you want. Then press
the

Tear Off (Font)

button to select the next setting you want

to change.

8. When you finish making settings, turn off the printer to exit

Default Setting mode.

Your new settings remain in effect until you change them again
or reset the printer’s defaults.

Restoring the printer’s default settings

If you want to restore all the factory default settings, turn off the
printer. Then hold down the

Load/Eject

LF/FF

, and

Pause

buttons while you turn on the printer.

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer


































































































































Результаты поиска

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer

Отзывы:

Похожие инструкции для C11C640001 - LX 300+II B/W Dot-matrix Printer

Бренды по названию

Популярные бренды

Epson C11C640001 - LX 300+II B/W Dot-matrix Printer, Справочное руководство

Результаты поиска

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer

Отзывы:

Похожие инструкции для C11C640001 - LX 300+II B/W Dot-matrix Printer

Бренды по названию

Популярные бренды