Epson AcuLaser Color 2000 Скачать руководство пользователя страница 95

Страница: 95 / 204

EPSON AcuLaser C2000

Revision C

Troubleshooting

Troubleshooting Method

3. Setting
environment

1. The place has vibration and
inclination.

Place the printer even and
stable place that is not
subject to vibration.

2. Temperature and Humidity
is not within the specification
described in Ch1.

Set the printer where there is
no fire nearby and no direct
air-conditioning wind.

3. The setting place is subject
to the direct sunlight.

Advice the customer to avoid
the direct sunlight using
curtain.

4. The setting place is dusty.

Avoid dusty place to set the
printer.

5. The ammonia gus is
generated from diazo copy or
floor detergent nearby.

Remove the printer from the
ammonia gus.

4. Paper size

The paper type and size is not
correct.

Advise the customer to use
paper which meets the
printer specification.

Table 3-2. Initial Check Point

Item

Symptom / Cause

Solution

5. Maintenance

The maintenance is not
performed properly.

Clean the paper path.

Replace the roller if the
surface is noticeably dirty.

The fusing belt is dirty.

Replace the oil coating roller.

6. Caution in the
winter

When setting the printer that
is cooled down by the fresh
air into the warm room,
condensation may be
generated inside and may
result in the following
symptoms.

• Lens is steamed up and the

image is too weak.

• Because of charging

failure, the image is too
strong.

• Because paper is wet,

paper is corrugated.

• Fusing becomes irregular.

Turn the printer ON and
leave the printer for about 20
minutes.

Open the drum and toner
cartridge after warming
them up with the room
temperature.

Table 3-2. Initial Check Point

Item

Symptom / Cause

Solution

Содержание AcuLaser Color 2000













































































































































































































Результаты поиска

Содержание AcuLaser Color 2000

Отзывы:

Похожие инструкции для AcuLaser Color 2000

Бренды по названию

Популярные бренды

Epson AcuLaser Color 2000, Руководство по обслуживанию

Результаты поиска

Содержание AcuLaser Color 2000

Отзывы:

Похожие инструкции для AcuLaser Color 2000

Бренды по названию

Популярные бренды