Epson AcuLaser Color 2000 Скачать руководство пользователя страница 82

Страница: 82 / 204

EPSON AcuLaser C2000

Revision C

Operating Principles

Printing Process

Figure 2-25. AIDC

Transfer Belt Cleaner Estrangement

Transfer belt cleaner is pressed or estranged to the transfer belt according
to its necessity.

Transfer belt cleaner turns cleaner motor ON, rotates cam to rotate
the lever holder, and pushes the (

↓

) part in Figure 2-26 down and

estrange the transfer belt cleaner from the transfer belt.

Belt cleaner estrangement position sensor is turned OFF and detects
the estrangement of the transfer belt cleaner.

Turns the cleaner motor ON and rotates the cam to loosen the lever
holder, and then presses the transfer belt cleaner to the transfer belt.

Pressure is added since the paper transfer is done until the belt goes
around.

Содержание AcuLaser Color 2000













































































































































































































Результаты поиска

Содержание AcuLaser Color 2000

Отзывы:

Похожие инструкции для AcuLaser Color 2000

Бренды по названию

Популярные бренды

Epson AcuLaser Color 2000, Руководство по обслуживанию

Результаты поиска

Содержание AcuLaser Color 2000

Отзывы:

Похожие инструкции для AcuLaser Color 2000

Бренды по названию

Популярные бренды