Epson AcuLaser Color 2000 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 204

background image

EPSON AcuLaser C2000

Revision C

Troubleshooting

Printer Message

103

Replace Photocondctr

Explanation
It is regarded that the photoconductor service life is end, based on
the total number of revolution of the photoconductor up to now
from previous replacement. And printing is stopped.

LED
The On Line LED and Continue LED are off.

Treatment Method
Open the Front Cover and replace Waste Toner Collector, Photo
conductor Unit and Print Head Filter with new ones.
Close the Front cover and the error will be canceled automatically.
The photoconductor counter is reset automatically and the panel
display “Photoconductor” in Setup Menu becomes 100%.

Replace Waste T Box

Explanation
The waste toner box has been sensed to be full of waste toner
from the engine, and printing is stopped.

LED
The On Line LED and Continue LED are off.

Treatment Method
Open the Front cover, then replace the Waste Toner Collector with
new one. Close the Front cover. The error will be canceled
automatically.

Replace Fuser

Explanation
It is regarded that the Fuser Unit service life is end, based on the
total number of revolution of the Fuser Unit up to now from
previous replacement. And printing is stopped.

LED
The On Line LED and Continue LED are off.

Treatment Method
Open the Cover-A and remove the Fuser Oil Roll, then replace the
Fuser Unit with new one. Reset the Fuser Oil Roll. Then open the
Cover-B and replace the 2nd Transfer Roll.

Replace Oil Roll

Explanation
End of Fuser Oil Roll life. The remaining life is counted in the
engine.

LED
The On Line LED and Continue LED are off.

Treatment Method
Open Cover A and replace Fuser Oil Roll with new one. Close
Cover A then the error will be cancelled automatically. Remaining
of Fuser Oil Roll returns 100%.

Replace Transfer Belt

Explanation
It is regarded that the Transfer Belt Unit service life is end, based
on the total number of revolution of the Transfer Belt up to now
from previous replacement. And printing is stopped.

LED
The On Line LED and Continue LED are off.

Treatment Method
Open the Front cover. Then remove the Photoconductor Unit and
replace the Transfer Belt Unit with new one. Then reset
Photoconductor Unit. Close the Front cover, then the error will be
canceled automatically.

Printer Open

Explanation
Front cover, Cover-A, Cover-B or Cover DM is/are open.

LED
The On Line LED and Continue LED are off.

Treatment Method
Close all cover and the error will be canceled automatically.

«
...
101
102
103
104
105
...
»

Содержание AcuLaser Color 2000













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AcuLaser Color 2000

Бренд: Malyan Страницы: 9

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 44

Бренд: Oki Страницы: 13

Бренд: Oki Страницы: 20

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 28

SCX-4300 - SCX 4300 B/W Laser

Бренд: Samsung Страницы: 4

ML-2240 - 23 Ppm Mono Laser Printer

Бренд: Samsung Страницы: 16

ML 2510 - B/W Laser Printer

Бренд: Samsung Страницы: 170

Бренд: Samsung Страницы: 165

Бренд: Xerox Страницы: 114

Power Defense PD3

Бренд: Eaton Страницы: 4

Бренд: Labelmate Страницы: 2

Бренд: Canon Страницы: 394

Бренд: Oce Страницы: 209

Бренд: Ricoh Страницы: 126

ColorQube 87 Series

Бренд: Xerox Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды