manualshive.com logo in svg

Epson 0C88832, Техническое руководство

Техническое руководство Epson 0C88832 предоставляет подробные инструкции для удобного использования продукта. Вы можете бесплатно скачать его с manualshive.com. Этот мануал поможет вам лучше понять функционал устройства и устранить возможные проблемы. Надежное руководство для успешного использования вашего устройства.

Поделиться
Скачать
background image

70

EPSON

E0C88832/88862 TECHNICAL MANUAL

5  PERIPHERAL CIRCUITS AND THEIR OPERATION (Clock Timer)

TMD0–TMD7: 00FF41H

The clock timer data can be read out.
Each bit of TMD0–TMD7 and frequency corre-
spondence are as follows:

TMD0: 128Hz

TMD4: 8Hz

TMD1: 64Hz

TMD5: 4Hz

TMD2: 32Hz

TMD6: 2Hz

TMD3: 16Hz

TMD7: 1Hz

Since the TMD0–TMD7 is exclusively for reading,
the write operation is invalid.
At initial reset, the timer data is set to "00H".

TMRST: 00FF40H•D1

Resets the clock timer.

When "1" is written: Clock timer reset
When "0" is written: No operation
Reading:

Always "0"

The clock timer is reset by writing "1" to the
TMRST.
When the clock timer is reset in the RUN status, it
restarts immediately after resetting. In the case of
the STOP status, the reset data "00H" is maintained.
No operation results when "0" is written to the
TMRST.
Since the TMRST is exclusively for writing, it
always becomes "0" during reading.

TMRUN: 00FF40H•D0

Controls RUN/STOP of the clock timer.

When "1" is written: RUN
When "0" is written: STOP
Reading:

Valid

The clock timer starts up-counting by writing "1" to
the TMRUN and stops by writing "0".
In the STOP status, the count data is maintained
until it is reset or set in the next RUN status. Also,
when the STOP status changes to the RUN status,
the data that was maintained can be used for
resuming the count.
At initial reset, the TMRUN is set to "0" (STOP).

PTM0, PTM1: 00FF20H•D0, D1

Sets the priority level of the clock timer interrupt.
The two bits PTM0 and PTM1 are the interrupt
priority register corresponding to the clock timer
interrupt. Table 5.8.3.2 shows the interrupt priority
level which can be set by this register.

Table 5.8.3.2  Interrupt priority level settings

At initial reset, this register is set to "0" (level 0).

ETM1, ETM2, ETM8, ETM32: 00FF22H•D0–D3

Enables or disables the generation of an interrupt
for the CPU.

When "1" is written: Interrupt enabled
When "0" is written: Interrupt disabled
Reading:

Valid

The ETM1, ETM2, ETM8 and ETM32 are interrupt
enable registers that respectively correspond to the
interrupt factors for 1 Hz, 2 Hz, 8 Hz and 32 Hz.
Interrupts set to "1" are enabled and interrupts set
to "0" are disabled.
At initial reset, this register is set to "0" (interrupt
disabled).

FTM1, FTM2, FTM8, FTM32: 00FF24H•D0–D3

Indicates the clock timer interrupt generation status.

When "1" is read:

Interrupt factor present

When "0" is read:

Interrupt factor not present

When "1" is written: Resets factor flag
When "0" is written: Invalid

The FTM1, FTM2, FTM8 and FTM32 are interrupt
factor flags that respectively correspond to the
interrupts for 1 Hz, 2 Hz, 8 Hz and 32 Hz and are
set to "1" at the falling edge of each signal.
When set in this manner, if the corresponding
interrupt enable register is set to "1" and the
corresponding interrupt priority register is set to a
higher level than the setting of interrupt flags (I0
and I1), an interrupt will be generated to the CPU.
Regardless of the interrupt enable register and
interrupt priority register settings, the interrupt
factor flag will be set to "1" by the occurrence of an
interrupt generation condition.
To accept the subsequent interrupt after interrupt
generation, re-setting of the interrupt flags (set
interrupt flag to lower level than the level indicated
by the interrupt priority registers, or execute the
RETE instruction) and interrupt factor flag reset are
necessary. The interrupt factor flag is reset to "0" by
writing "1".
At initial reset, this flag is reset to "0".

PTM1

PTM0

Interrupt priority level

1

1

0

0

1

0

1

0

Level 3 (IRQ3)

Level 2 (IRQ2)

Level 1 (IRQ1)

Level 0 (None)

Содержание 0C88832
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 0C88832

dbx 902 Manual preview
902
Бренд: dbx Страницы: 8
NEC Univerge SV9300 Migration Manual preview
Univerge SV9300
Бренд: NEC Страницы: 26
NEC NEAX 2400 Quick Reference Manual preview
NEAX 2400
Бренд: NEC Страницы: 20
NEC DS2000 IntraMail Instructions preview
DS2000 IntraMail
Бренд: NEC Страницы: 2
Aastra CNX Product Brief preview
CNX
Бренд: Aastra Страницы: 2
Xinje XG Series User Manual preview
XG Series
Бренд: Xinje Страницы: 76
Dust Networks SmartMesh IA-510 D2511 Manager'S Manual preview
SmartMesh IA-510 D2511
Бренд: Dust Networks Страницы: 30
Mitsubishi 32172 User Manual preview
32172
Бренд: Mitsubishi Страницы: 874
Mellanox Technologies ConnectX 3 Pro User Manual preview
ConnectX 3 Pro
Бренд: Mellanox Technologies Страницы: 57
NC-link NC-AP111 User Manual preview
NC-AP111
Бренд: NC-link Страницы: 20
Technics SH-GE90 Service Manual preview
SH-GE90
Бренд: Technics Страницы: 20
Doremi MB-4K User Manual preview
MB-4K
Бренд: Doremi Страницы: 15
Meinberg CPU-C15G2 Setup Manual preview
CPU-C15G2
Бренд: Meinberg Страницы: 14
Crown PIP-AF Owner'S Manual preview
PIP-AF
Бренд: Crown Страницы: 7
McIntosh MX160 Owner'S Manual preview
MX160
Бренд: McIntosh Страницы: 44
IBM 7311-D11 Removal And Replacement Procedures preview
7311-D11
Бренд: IBM Страницы: 74
PairGain 150-2230-01 Quick Installation Manual preview
150-2230-01
Бренд: PairGain Страницы: 48
7th Sense Pixel Processing Juggler User Manual preview
Pixel Processing Juggler
Бренд: 7th Sense Страницы: 148

Бренды по названию

Популярные бренды

Загрузить еще бренды