background image

 

1

Preface 

Thank you for choosing 

EPA

’s VFD-L series AC Drive.  The VFD-L series is manufactured  using 

high-quality components, material and incorporating the latest microprocessor technology available. 

This manual will help in the installation, parameter setting, troubleshooting, and daily maintenance of 
the AC motor drive. To guarantee safe operation of the equipment, read the following safety 
guidelines before connecting power to the AC motor drive. Keep this operating manual handy and 
distribute to all users for reference. 

Important Notes: 

 

DANGER! 

AC input power must be disconnected before any maintenance. Do not connect or 

disconnect wires while power is applied to the circuit. Only qualified technicians should perform 
maintenance on the VFD-L.

  

 

CAUTION! 

There are highly sensitive MOS components on the printed circuit boards. These 

components are especially sensitive to static electricity. To avoid damaging these components, 
do not touch the circuit boards with metal objects or your bare hands.

  

 

DANGER! 

A charge may still remain in the DC-link capacitor with hazardous voltages even 

after the power has been turned off. To avoid personal injury, do not remove the cover of the AC 
drive until all “DISPLAY LED” lights on the digital keypad are off.  Please note that there are live 
components exposed when the AC drive is open,. Be careful to not touch these live parts.

  

 

CAUTION! 

Ground the VFD-L using the ground terminal.       The grounding method must 

comply with the laws of the country where the AC drive is to be installed.

 

 

DANGER! 

The AC drive may be destroyed beyond repair if power is misapplied to the 

input/output terminals. Never connect the AC drive output terminals U/T1, V/T2, W/T3 directly 
to the AC main circuit power supply.

  

  

Содержание VFD-L series

















Отзывы: