entegris NOWPak Скачать руководство пользователя страница 28

Страница: 28 / 34

NOWPAK LINER-BASED CANISTER SYSTEM

User Manual | Entegris, Inc.

APPENDIX A: REQUIRED TOOLS

—

Entegris provides the following specialized tools for filling, operation, and maintenance of the liner-based
canister system.

Contact Entegris at +1 978 436 6500 to order these tools.

TOOL

PART NUMBER

Torque wrench
(1/2” drive)

NA-18 (4- to 40-liter)

NA-33 (3/8" drive with 1/2" adapter,
4- to 40-liter) for use with NC-W2
polypropylene closure

NA-92 (200-liter)

Torque adapter tool

NA-10 (4- to 40-liter with
two-piece NC-03 or NC-04-type
aluminum closure)

NA-03 (20-liter with
one-piece NC-W2 polypropylene
closure)

DA-06 (200-liter)

CONTAINER SIZE

TORQUE WRENCH TO OPEN AND
CLOSE CANISTER CLOSURE

USED WITH THIS TORQUE ADAPTER TOOL

4- to 40-liter (with
two-piece closure)

NA-18

NA-10

4- to 40-liter (with
one-piece closure)*

NA-33

NA-03

200-liter

NA-92

DA-06

Diptube removal tool

NA-13

* Either the NA-33 or the NA-18 may be used to torque the NC-W2 polypropylene closure.

Содержание NOWPak



































Результаты поиска

Содержание NOWPak

Отзывы:

Похожие инструкции для NOWPak

Бренды по названию

Популярные бренды

entegris NOWPak, Руководство пользователя

Результаты поиска

Содержание NOWPak

Отзывы:

Похожие инструкции для NOWPak

Бренды по названию

Популярные бренды