enraf Ensite Pro Скачать руководство пользователя

Страница: 53 / 80

Modbus settings

Instruction manual Ensite Pro Configuration Tool

Page 53

If any changes are made to any of the CIU Plus settings
(while a hot standby counterpart is defined), the program will warn
to keep the configurations of both units synchronous.

Press the ‘arrow left’-button to move the highlighted entity in the
‘ID’-column to the ‘Available Entities’-column.

Press the ‘arrow right’-button to move the highlighted entity in the
‘Available entities’-column to the ‘ID’-column.

Entity ID number

Name

Entity name

type

Entity type / dimension

Size

Number of registers

Scale

Scaling factor

offset

Offset value

Entity

When in the list an entity is highlighted, it is possible to change the
type, size, scale and/or offset.

Press the ‘Default’-button to restore “Entis Pro default’ default
settings.

Hot standby

Содержание Ensite Pro

















































































Результаты поиска

Содержание Ensite Pro

Отзывы:

Похожие инструкции для Ensite Pro

Бренды по названию

Популярные бренды

enraf Ensite Pro, Инструкция по эксплуатации

Результаты поиска

Содержание Ensite Pro

Отзывы:

Похожие инструкции для Ensite Pro

Бренды по названию

Популярные бренды