EnOcean LEDRU Скачать руководство пользователя

Страница: 8 / 8

LEDRU LED 0-10V Zone Controller Installation Guide

LEDRU-W-EO / LEDRU-W-AU DD08 and up

Page

Parameter

Description

Default /

Notes

System Parameters

MinVoltageLevel

Minimum 0-10V output voltage

level when light is switched ON

1.0V

MaxVoltageLevel

Maximum 0-10V output voltage

level when light is switched ON

10.0V

0-10VRelayDelay

Delay between switching the relay

on and starting to ramp up the 0-
10V output

50ms

ModeAfter-

PowerLoss

ModeAfterPowerLoss

(ON/OFF/LAST STATE)

LAST STATE

StatusMessage-

Timer

Defines, how often status messages

are transmitted (seconds, 0=off,
0xFFFF=only event based)

0xFFFF

RepeaterFunction

Defines the repeater level of the

device (OFF/1-Level/2-Level)

OFF (disabled)

RepeatLinked-

DevicesOnly

Configures the repeater to only

repeat telegrams from devices
linked to it

ON (enabled)

Enable-

DebugMessages

Enable or disable debug messages

OFF (disabled)

EnableLink-

Checker

Enable or disable link checker

(if a learn telegram from a linked
device is received while in
operating mode, the 0-10V output
will toggle once between 10% and
90%)

ON (enabled)

Switch diming

curve

Defines four different diming

curved

Linear curve

Enable relay on

permanently

Relay out line voltage will not be

cut off if enabled

Disabled

Accumulated

uptime value

Accumulated time for output = On n/a

Average output

value

Average output dim level over

entire usage while output is on

n/a

Fixed output level Light level used for On after power

loss (if on is selected, see Mode
AfterPowerLoss) of for a short
rocker click “I”

75%

Fixed output on

Short rocker click”I” sets output

value to FixedOutput Level if
enabled, otherwise to last state
before turned off.

disabled

Status reporting

EEP

Defines outbound EEP

D2_40_00

Link Health Mode Can be used to check RSSI levels of

inbound links, LED controller will
send a special message for every
link based event or the entire
network

disabled

Secure telegram

type

Sets encryption to standard or

advanced

Standard

Device

identification 1-6

Can be used to store a string of

Characters in the LED EEPROM for
the purpose of naming the device
or the location

n/a

Содержание LEDRU









Результаты поиска

Содержание LEDRU

Отзывы:

Похожие инструкции для LEDRU

Бренды по названию

Популярные бренды

EnOcean LEDRU, Руководство по установке

Результаты поиска

Содержание LEDRU

Отзывы:

Похожие инструкции для LEDRU

Бренды по названию

Популярные бренды