Enlogic EN1201 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 56

Enlogic EN1201 Скачать руководство пользователя страница 21

The Critical Component

EN Series User Manual

21

2.  Select the Block user on login failure checkbox.
3.  Set the Maximum number of failed logins.
4.  Set the length of time that must pass before the user may attempt login again. Use the Block Timeout dropdown

menu provided.

5. Select OK to save the changes

Login limitations determine how long users are permitted to stay idle before being forced out of the system.

1.  Go to Device Configurations > Security > Login Settings
2.  In the Login Settings dialog box, select the go to the Login Limitations.
3.  Choose the Idle Timeout Period from the dropdown menu.
4.  Select OK to save changes.

Password Policy

You may set a requirement for users to change their password at set intervals using the Password Aging Interval

policy. You may also specify criteria for passwords to ensure that your users enter strong passwords.

1.  Go to Device Configurations > Security > Password Policy
2.  If desired, choose a password aging interval from the Password Interval dropdown menu.
3.  If you wish to specify password criteria, select the Strong Passwords checkbox.
4.  Set the minimum and maximum password length via the dropdown menus provided. Note that the minimum

password length cannot be below 8 characters and the maximum allowed is 32.

5. Select the checkboxes to force users to use specific types of characters within the password.
6. Select OK to save the changes.

Event Rules

Event rules are situations in which the EN Series PDU notifies and reacts to certain conditions. These rules can

be created to respond to various events.

An event rule has two parts:

1. Event: the situation where the PDU meets a certain condition (i.e., a temperature sensor exceeds the warning

limit.)

2. Action: the response to the event (i.e., send an SMTP message, SNMP trap.)

To create a new event rule, you must:

1. Go to Device Configuration > Event Rules.
2. Select the checkbox next to the Event Rules and Actions you want to setup.

3. Select OK.

«
...
19
20
21
22
23
...
»

Содержание EN1201

























































Отзывы:

Нет отзывов