Engler ADS 2000 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 37

background image

Troubleshooting cont.

If the

Battery Low

LED stays on after the unit has been powered you may have one of

the following problems:

a.

There is no power in the wall socket that you are connecting the unit to.

b.

The power adapter is damaged.

c.

The battery has expired and needs to be replaced. To have the battery replaced,
send the unit to Engler Engineering Corporation. See engler411.com for return,
repair, and loaner forms, click the “repair” tab..

d.

The female power socket in the back of the ADS 2000 has been damaged. See
engler411.com for return, repair, and loaner forms, click the “repair” tab.

6. Make sure that the

Gas Sampling System

is connected properly.

To connect the

Gas Sampling System

, insert the

Luer Lock

connector to the

Gas

Sampling

input and rotate it clockwise one half turn. Now insert the

Gas Sampling

elbow into the end of the Breathing Circuit.

7. Inspect the all ADS 2000 hoses periodically to make sure that they are properly

connected, and not kinked, cracked, or broken.

28

Engler Engineering Corporation

ADS 2000

«
...
26
27
28
29
30
...
»

Содержание ADS 2000






































Отзывы:

Нет отзывов

Похожие инструкции для ADS 2000

Бренд: BANLAW Страницы: 32

Бренд: Baker Instrument Company Страницы: 24

Бренд: Navman Страницы: 17

Бренд: NORLUX Страницы: 2

Бренд: Taylor Страницы: 70

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренд: Ecco Страницы: 17

Бренд: Haag-Streit Страницы: 16

Бренд: IFM Страницы: 175

Бренд: IFM Страницы: 5

Бренд: K-LASER Страницы: 70

Бренд: K-LASER Страницы: 72

Бренд: Tanco Страницы: 112

Бренд: Valmar Страницы: 78

Бренд: Valhalla Scientific Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды