Engler ADS 2000 Скачать руководство пользователя страница 9

Страница: 9 / 37

etting familiar with the ADS 2000

cont.

BREATHING CIRCUIT PORTS

- Connect the breathing circuit to these ports.

BATTERY LOW INDICATOR / SAFETY ALARM

- The red led on the front panel of

the ADS 2000 is a warning indicator that the battery power is low, and that the unit
should be placed on charge immediately. When the unit is first powered up the led will
self test by flashing on and then should remain off.

The LED will also flash if the external sampling hose is disconnected.

GAS SAMPLING INPUT

- To connect the Gas Sampling System, insert the

Luer lock

connector to the Gas Sampling input and rotate it clockwise one half turn. The

Luer

lock

connector is located at the end of the 1/8” clear tube. Locate the other

Luer lock

connector at the other end of the 1/8” clear tube. Connect it to the Gas Sampling elbow
on the Breathing Circuit.

Note: It is imperative that the Gas Sampling Hose stay connected during use.

Rear View:

SCAVENGER OUT

- Connect one end of the blue "

Scavenger

" tubing to this port and

connect the other end to a scavenging filter canister or other scavenging device, either
active or passive.

FROM VAPORIZER

- Connect one end of the "

From Vaporizer

" hose to this

port and connect the other end to the outlet port of your precision vaporizer.

TO VAPORIZER

- Connect one end of the "

To Vaporizer

" hose to this port and

connect the other end to the inlet port or your precision vaporizer.

OXYGEN IN

- Connect one end of the green "

Oxygen

" hose to this port and connect

the other end to an oxygen source that is set to a pressure of

50 PSI

(pounds per

square inch).

POWER INLET

- Connect your power cord to this port.

ALARM

- This is the alarm speaker.

50 PSI / 5 PSI TOGGLE

- This is the manual control to alternate between the

50 PSI

(normal) operating mode and the

5 PSI

, (lab) mode.

ADS 2000

Engler Engineering Corporation

Содержание ADS 2000






































Результаты поиска

Содержание ADS 2000

Отзывы:

Похожие инструкции для ADS 2000

Бренды по названию

Популярные бренды

Engler ADS 2000, Руководство пользователя

Результаты поиска

Содержание ADS 2000

Отзывы:

Похожие инструкции для ADS 2000

Бренды по названию

Популярные бренды