Enfinity 1000TL Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 40

background image

6

!

CauTION!
Possible damage to health as a result of the effects of radiation!

• Do not stay closer than 20 cm to the inverter for any length of time.

NOTE:
Grounding the PV generator.

Comply with the local requirements for grounding the PV modules and the PV
generator. Enfinity recommends connecting the generator frame and other
electrically conductive surfaces in a manner which ensures continuous conduction
and ground these in order to have optimal protection of the system and personnel.

2.3 Explanation of symbols

This section gives an explanation of all the symbols shown on the inverter and on the type label.

• Symbols on the inverter

Symbol

Explanation

Danger to life due to high voltages in the inverter!

There is residual voltage in the inverter. The inverter requires 5

minutes to discharge.

• Wait 5 minutes before you open the upper lid or the DC lid.

• Symbols on the product label

Symbol

Explanation

CE mark.

The inverter complies with the requirements of the applicable

CE guidelines.

Beware of hot surface.

The inverter can become hot during operation. Avoid contact

during operation.

Danger of high voltages.

Danger to life due to high voltages in the inverter!

«
...
4
5
6
7
8
...
»

Содержание 1000TL









































Отзывы:

Нет отзывов

Похожие инструкции для 1000TL

Бренд: Microtek Страницы: 17

Бренд: B&K Страницы: 2

Бренд: Magtek Страницы: 54

Бренд: CYP Страницы: 16

AZZYRRO 3-6-ZSS-HP

Бренд: ZCS Страницы: 65

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology 8R

Бренд: M-Audio Страницы: 25

Бренд: Advantech Страницы: 4

Бренд: ADF Web Страницы: 31

Бренд: SMA Страницы: 56

Бренд: M2TECH Страницы: 49

Бренд: Renishaw Страницы: 15

Бренд: Micno Страницы: 29

Бренд: Renaissance Learning Страницы: 2

E-PSW-SX-01(SC)

Бренд: Transition Networks Страницы: 6

Бренд: Uniteck Страницы: 24

UNIMPPT 60/10.24L

Бренд: Uniteck Страницы: 67

Бренд: CYP Страницы: 64

Бренд: Fulling Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды