background image

Smartec S CLD134

Commissioning

Hauser

11

C124

Calculated cell
constant is displayed

0.1 ... 

6.3

 ... 9.99 cm

-1

6.300 1/cm
Cellconst

The calculated cell constant is displayed 
and entered in A5.

C125

Calibration status is 
displayed

o.k.
E xxx

o.k.
Status

If the calibration status is not o.k., the 
second display line shows an explanation 
of the error.

C126

Store calibration 
results

yes

no
new

yes
Store

If C125 = E xxx, then only no or 

new

.

If new, return to C.
If yes/no, return to “Measurement”.

C1(3)

Calibration with 
sensor adaptation for 
inductive sensors

Airs=airset (1)
Cellc= cell constant (2)

InstF=installation 
factor(3)

InstF
Calibrat

Sensor calibration with compensation of 
wall influence.
The distance from the sensor to the pipe 
wall and the pipe material (conductive or 
nonconductive) influence the measured 
value. The installation factor compensates 
this influence.

The sensor is installed in the process.

C131

Enter process 
temperature

25 °C

-35.0 ... 250.0 °C

25.0 °C
MTC temp.

Only exists if B1 = fixed.

C132

Enter 

α

 value of 

calibration solution

2.10 %K

0.00 ... 20.00 %K

2.10 %K
alpha value

This value is specified in the Technical 
Information of all E+H calibration 
solutions. You can also use the printed-on 
table to calculate the value.
Set 

α

 to 0 for calibration with 

uncompensated values.

C133

Enter correct 
conductivity value of 
calibration solution

current measured value

0.0 ... 9999 mS/cm

10.30 mS/cm
Real val.

Determine the correct conductivity value 
by a reference measurement.

C134

Calculated 
installation factor is 
displayed

1

0.10 ... 5.00

1
InstFact

The distance of the sensor to the pipe wall 
and the pipe material (conductive or 
nonconductive) influence the measured 
value. The installation factor compensates 
this influence.

C135

Calibration status is 
displayed

o.k.
E xxx

o.k.
Status

If the calibration status is not o.k., the 
second display line shows an explanation 
of the error.

C136

Store calibration 
results?

yes

no
new

yes
Store

If C135 = E xxx, then only no or 

new

.

If new, return to C.
If yes/no, return to “Measurement”.

Code

Field

Selection or range

Display

Info

Содержание Smartec S CLD134













Отзывы: