Endress+Hauser Liquisys M CLM 223 Скачать руководство пользователя страница 9

Страница: 9 / 83

2.4

Monitoring and safety features

Safety features

The transmitter is protected against external
influences and damage by the following
design measures:

• Rugged housing
• Degree of protection provided by

enclosure: IP 65 (CLM 253)

• UV resistance

Monitoring features

In the event of a system error or power failure,
an alarm condition is signalled via a fault-
signalling contact.

2.5

Immunity to interference

This instrument has been tested according to
the applicable European standards for
industrial applications with regard to
electromagnetic compatibility. It is protected
against electromagnetic interference by the
following design measures:

• Cable screen
• Interference suppressor filter
• Interference suppression capacitors

Warning:

The specified immunity to
interference only applies for devices
connected as outlined in these
operating instructions.

2.6

Certificate of conformity

The CLM 223/253 transmitter has been
developed and manufactured in accordance
with currently valid European standards and
directives.

Note:

An EC certificate of conformity is
supplied.

LM253E02.CHP

Liquisys M CLM 223 / 253

Safety

Hauser

Содержание Liquisys M CLM 223




















































































Результаты поиска

Содержание Liquisys M CLM 223

Отзывы:

Похожие инструкции для Liquisys M CLM 223

Бренды по названию

Популярные бренды

Endress+Hauser Liquisys M CLM 223, Руководство по эксплуатации

Результаты поиска

Содержание Liquisys M CLM 223

Отзывы:

Похожие инструкции для Liquisys M CLM 223

Бренды по названию

Популярные бренды