Endress+Hauser Liquisys M CLM 223 Скачать руководство пользователя страница 10

Страница: 10 / 83

Installation

The following procedure should be followed
for a complete measuring system installation:

• Installation or attachment of transmitter

(see chapter 3.3)

• Selection and connection of cable and

measuring cell (see chapters 3.4, 3.5
and 9)

• Installation is followed by start-up (see

chapter 5).

3.1

Measuring system

The complete measuring system comprises:

• The Liquisys M CLM 223 or CLM 253

transmitter

• A measuring cell with or without an

integrated temperature sensor

• A measuring cable CYK 71 (conductive

measurement) or measuring cable CLK 5
(cable for inductive measurement
permanently attached to sensor)

Optional:

• Extension cable CYK 71 (conductive)

or CLK 5 (inductive)

• Junction box VBM

HAUSER
LIQUISYS

CAL

REL

REL 1

ALARM

REL 2

HAUSER
LIQUISYS

CAL

REL

REL 1

ALARM

REL 2

LM253SYS.CDR

Immersion assembly

CLA 111

CLS 15

(conductive measuring

cell) with integr.

Pt 100

Measuring cell CLS 21

(conductive measuring cell)

with integr. Pt 100

CLS 50

(inductive measuring cell)

with integr. Pt 100

Liquisys M CLM 253

Liquisys M CLM 223

Fig. 3.1

Complete measuring
systems consisting of
Liquisys M CLM 223 / 253
with measuring cable,
assembly and conductivity
measuring cell

Installation

Liquisys M CLM 223 / 253

Hauser

Содержание Liquisys M CLM 223




















































































Результаты поиска

Содержание Liquisys M CLM 223

Отзывы:

Похожие инструкции для Liquisys M CLM 223

Бренды по названию

Популярные бренды

Endress+Hauser Liquisys M CLM 223, Руководство по эксплуатации

Результаты поиска

Содержание Liquisys M CLM 223

Отзывы:

Похожие инструкции для Liquisys M CLM 223

Бренды по названию

Популярные бренды