background image

Deltapilot S

18

Hauser

Operating conditions (installation)

Installation instructions for 
compact version DB50, 
DB50A, DB50L, DB50S  

• Always install the device under the lowest measuring point.
• Do not install the device at the following positions:

In the filling curtain, in the tank outlet or at a point in the tank that can be reached by pressure pulses from 
the agitator.

• The calibration and functional test can be carried out more easily if you mount the device after a shut-off 

device.

• Deltapilot S must be included in the insulation for media that can harden when cold. The use of rod or cable 

versions is also possible.

Installation instructions for 
rod and cable versions 
DB51(A), DB52(A) and 
DB53(A)  

• When mounting the rod and cable versions, make sure that the probe head is located at a point as free as 

possible from flow. To protect the probe from impact from lateral movement, mount the probe in a guide 
tube (preferably made of plastic) or secure it with a clamping fixture. For devices for Ex-areas, see Safety 
Instructions (XAs).

• The length of the extension cable or the probe rod is based on the planned level zero point. The top of the 

probe should be at least 5 cm under this. 

Supplementary installation 
instructions

Process diaphragm

• Do not use sharp or hard objects to handle or clean the process diaphragm. Build-up has no effect on the 

measurement result as long it is porous and does not present a mechanical load on the diaphragm of the 
pressure measuring cell.

• The process diaphragm on all Detapilot S rod and cable extension is protected against mechanical damage 

by means of a plastic cover.

Seal

• Deltapilot S with G 1 1/2 thread:

When screwing the device into the tank, the flat seal supplied must be placed on the sealing surface of the 
process connection.

• Deltapilot S with NPT thread:

– Wrap and seal the thread with Teflon tape.
– Tighten the device at the hexagon head only. Do not turn the device by the housing.
– Do not screw in the thread too tightly. Max. torque: 20...30 Nm

Sealing the probe housing

It is important that no moisture enters the housing while mounting the probe, connecting the electronic insert 
and operating the measuring system.
• Always screw the housing cover and the cables entries tight.
• The O-Ring seal in the housing cover and the thread of the aluminum cover are lubricated. If this lubrication 

has been removed, replace it with silicone grease or graphite paste, for example, so that the cover seals tight. 
Do not use mineral-oil based greases. These can destroy the O-ring.

Содержание Deltapilot S DB50





























































Отзывы: