Emerson Rosemount ET310 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 52

background image

Figure 4-3: Sensor with brackets assembled and the protective
cap fitted

A. Bolt heads

3. Hold the brackets in position, using a torque wrench and an allen key

to tighten the fasteners to 14Nm.

4.2

Commissioning the sensor for the magnetic fixture

Commissioning allows the sensor to securely join a designated network and
communicate with a gateway. The IK220 installation kit comes with a
commissioning interface (CC21) and a tablet PC with the Permasense
installation application installed. The CC21 provides an electronic interface
between the ET310 sensor and the tablet PC during commissioning.

The installation application software is used to

1. Provision the WiHART network configuration on the sensor.

2. Monitor the quality of the ultrasonic signal during mechanical

installation.

Both of these steps are required to complete the commissioning.

Note

All the sensors connected to the network and Gateway must have the same
network ID and Join Key.

Procedure

1. Power up the rugged tablet PC and connect the CC21 commissioning

interface to the tablet PC USB port.

January 2022

Quick Start Guide

Quick Start Guide

27

«
...
25
26
27
28
29
...
»

Содержание Rosemount ET310





















































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount ET310

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: Jafar Страницы: 9

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 32

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Lattice Semiconductor Страницы: 2

Бренд: Lathem Страницы: 4

Бренд: tams elektronik Страницы: 36

Бренд: RADEMACHER Страницы: 48

GRASS VALLEY MDX-3901

Бренд: Belden Страницы: 45

TBEN-L 8IOL Series

Бренд: turck Страницы: 148

APEXpy 07-37A2-2111/ 520Series

Бренд: Bartec Страницы: 98

Бренд: SAGEMCOM Страницы: 2

Бренд: Instant Care Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды