Emerson Rosemount Clarity II T56 Скачать руководство пользователя страница 13

Страница: 13 / 60

Install

2.1

Unpack and inspect

Consult the table to verify that you have received the parts for the option you ordered.

Table 2-1: Rosemount T56 Turbidmeter Parts

Item

Model/part number

Single input turbidity transmitter with HART

56-03-27-38-HT

Dual input turbidity transmitter with HART

56-03-27-37-HT

Sensor - EPA standards

8-0108-0002-EPA

Sensor - ISO standard

8-0108-0003-ISO

Cable - 3 ft. (0.9 m)

2413800

Cable - 20 ft. (6.1 m)

2409700

Cable - 50 ft. (15.2 m)

2409800

Calibration cup

2410100

Molded chamber/debubbler

24170-00

2.2

General installation information

1. Although the transmitter is suitable for outdoor use, do not install it in direct

sunlight or in areas of extreme temperatures.

2. Install the transmitter in an area where vibration and electromagnetic and radio

frequency interference are minimized or absent.

3. Keep the transmitter and sensor wiring at least one foot (0.3 m) from high voltage

conductors. Be sure there is easy access to the transmitter.

4. The transmitter is suitable for panel, pipe, or surface mounting. Refer to the figures

below.

WARNING

Electrical shock

Electrical installation must be in accordance with the National Electrical Code (ANSI/
NFPA-70) and/or any other applicable national or local codes.
Do not operate or energize instrument with case open.

Note

Dimensions are in inches (millimeters).

1. Panel supplied by others. Maximum thickness: 3.75 in. (9.52 mm)

2. 4X mounting brackets and screws provided with instrument

Reference Manual

Install

00809-0100-3565

July 2020

Rosemount T56

Содержание Rosemount Clarity II T56





























































Результаты поиска

Содержание Rosemount Clarity II T56

Отзывы:

Похожие инструкции для Rosemount Clarity II T56

Бренды по названию

Популярные бренды

Emerson Rosemount Clarity II T56, Справочное руководство

Результаты поиска

Содержание Rosemount Clarity II T56

Отзывы:

Похожие инструкции для Rosemount Clarity II T56

Бренды по названию

Популярные бренды