Wing
Nut
T-fitting
1/4" Diameter
Tube
Cold Water
Supply Line
6
Compression valve or T-fitting option
(not supplied):
En
s
ure that a
s
hutoff valve i
s
in
s
talled
on the cold water
s
upply line. If
s
o, a
T-fitting or compre
ss
ion valve can be
u
s
ed to connect the di
s
pen
s
er.
Connect the 16" (40.6 cm) long, 1/4"
diameter copper tube on the
di
s
pen
s
er to the T-fitting a
s
s
hown
(
s
ee
s
tep 4).
3
WATER CONNECTION OPTIONS
Attach the valve to a
cold water supply line
.
Shutoff valve option (not supplied):
The water connection can be made
u
s
ing a
s
hutoff valve. Thi
s
i
s
a more
complex in
s
tallation and
s
hould only
be attempted by an experienced
in
s
taller with the proper
k
nowledge
and tool
s
.
Saddle valve option (not supplied):
Follow the direction
s
for
“
s
elf-piercing attachment”
included with the valve.
Connect the 16" (40.6 cm) long, 1/4"
diameter copper tube on the di
s
pen
s
er
to the
s
addle valve a
s
s
hown (
s
ee
s
tep 4).
Open the valve and let a
s
mall amount
of water run through it into a pan.
Thi
s
will flu
s
h the line of
s
ediment.
2
R
emove the
s
pout by loo
s
ening
the
s
et
s
crew in
s
pout holder
approximately 2 full turn
s
and
pull out
s
pout.
Mount the unit through the 1 3/8"
diameter (35 mm) hole in the
s
in
k
.
Ma
k
e
s
ure the valve lever i
s
in the
up po
s
ition and feed the
s
pout end
of the di
s
pen
s
er through the
s
in
k
mounting hole.
A
C
INSTALLING THE DISPENSER
While holding the di
s
pen
s
er in
place with
s
pout removed,
s
lip
the rubber ga
sk
et and mounting
nut over the valve lever and
hand tighten the nut on the
threaded barrel.
Align
s
pout
s
o water run
s
into the
s
in
k
and
s
ecure the di
s
pen
s
er by
tightening the wing nut from the
under
s
ide of the
s
in
k
.
B
Personal Injury:
Fail
u
re to ti
g
hten
s
et
s
crew allow
s
ea
s
y
removal of
s
po
u
t. Operation of
u
nit with
s
po
u
t remove
d
co
u
l
d
ca
us
e inj
u
ry from hot water
s
pray
.
Mounting
Nut
Rubber
Gasket
7
D
Rea
ss
emble the
s
pout en
s
uring
the rubber
s
eal i
s
in place on inner
s
pout tube grove before re-in
s
erting
s
pout into tan
k
outlet.
If rubber
s
eal i
s
not on
s
pout, chec
k
in
s
ide tan
k
outlet. Remove and
in
s
tall
s
eal per diagram.
Pu
s
h
s
pout into di
s
pen
s
er a
s
far a
s
it will go and tighten
s
et
s
crew.
Spout
Rubber
Seal
Saddle valves are susceptible
to clogging
.
The dispenser must be mounted in
the upright (vertical) position only.
Spout and spout holder should not be loose
after mounting. First tighten mounting nut
and then tighten wing nut securely.
