manualshive.com logo in svg

Emerson FloBoss 103, Инструкция по эксплуатации

Поделиться
Скачать
Emerson FloBoss 103 Скачать руководство пользователя страница 86

FloBoss 103/104 Instruction Manual 

9-2 

Troubleshooting 

Revised August-2017 

9.2  Troubleshooting Checklists 

9.2.1  Dial-up Modem 

If you are experiencing troubles with an internal 

dial-up modem

: 

▪

 

Check to make sure you’ve applied power to the FB100. Check the 
ON/OFF jumper, the wiring connections at CHG+ and CHG-, and 
the wiring at the power source. 

▪

 

Check the wiring to the modem (see 

Chapter 5)

. 

▪

 

Check the communication port settings in ROCLINK 800. Refer to 

ROCLINK 800 Configuration Software User Manual

 (Part 

D301159X012).   

▪

 

Check the modem INIT string as displayed in the communication 
port settings in ROCLINK 800. Refer to 

ROCLINK 800 

Configuration Software User Manual

 (Part D301159X012).  

9.2.2  Serial Communications 

If you are experiencing troubles with a 

serial communications

 

connection (LOI, EIA-232, or EIA-485): 

▪

 

Check to make sure you have applied power to the FB100. Check 
the ON/OFF jumper, the wiring connections at CHG+ and CHG-, 
and the wiring at the power source. 

▪

 

Check the wiring to the termination block or connector (see 

Chapter 

5)

. 

▪

 

Check the communication port settings in ROCLINK 800. Refer to 

ROCLINK 800 Configuration Software User Manual

 (Part 

D301159X012).  

9.2.3  Optional I/O 

If you are experiencing troubles with an optional 

I/O point

 (Analog 

Input, Analog Output, Discrete Input, Discrete Output, or Pulse Input): 

▪

 

Check (using ROCLINK 800) to see how the channel is configured.   

▪

 

If the configuration looks correct, then simulate an input (within the 
range of the input) or force an output to be produced using 
ROCLINK 800 software. 

▪

 

If the types of I/O available for configuration do not match the type 
of I/O wired to the I/O terminations, check the I/O Setup screen. 
Refer to 

Chapter 4

 for wiring schematics and instructions. 

▪

 

If an input channel is in question, you may be able to use one of the 
outputs (known to be in working order) to simulate the required 
input. Likewise, if an output channel is in question, you may able to 
connect it to a working input channel and check the results. 

Содержание FloBoss 103











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды