manualshive.com logo in svg

Emerson FloBoss 103, Инструкция по эксплуатации

Поделиться
Скачать
Emerson FloBoss 103 Скачать руководство пользователя страница 49

FloBoss 103/104 Instruction Manual 

Revised August-2017 

Power Connections 

3-7 

In these circumstances, 

remove

 the battery charger module (part 

W38231X0032) and use the FB103 or FB104 

without

 internal power 

batteries. Refer to 

Section 3.5.3, Replacing the Batteries

, for instructions 

on removing the battery charger module or contact Remote Automation 
Solutions LifeCycle Services for assistance in removing the battery 
charger module. 

3.5.2 

Determining Battery Requirements 

To determine the system capacity requirements, multiply the system 
current load (I

SF

) on the batteries by the amount of reserve time 

required. Compute “I

SF

” as described in 

Section 3.3, Determining Power 

Requirements.

 The equation is as follows: 

 

System Requirement = I

SF

 amps 

 Reserve hrs = _____ amp-hrs 

3.5.3 

Replacing the Batteries 

The battery pack contains three D-size lead-acid batteries providing 2.5 
Amp-hours of current at 6.2 volts nominal. 

 

Caution

 

When installing equipment in a hazardous area, ensure that all 
components are approved for use in such areas.  Check the product 
labels. Change components only in an area known to be non-hazardous. 
Performing these procedures in a hazardous area could result in 
personal injury or property damage. 

To avoid circuit damage when working inside the unit, use appropriate 
electrostatic discharge precautions, such as wearing a grounded wrist 
strap. 

 

To replace the battery pack: 

1. 

Unscrew the front end (LCD end) cap cover.  

2. 

Place the power jumper (located at J1 on the Battery Charger 
module) in the OFF position. 

3. 

Remove the ribbon cable from the Battery Charger module to the 
Backplane Board. 

4. 

Remove the four screws from the Battery Charger module. 

5. 

Remove the Battery Charger module. 

6. 

Replace the Battery Charger module. 

7. 

Replace the four screws from the Battery Charger module. 

8. 

Replace the ribbon cable from the Backplane Board to the Battery 
Charger Board. 

9. 

Place the power jumper (located at J1 on the Battery Charger 
module) in the ON position. 

10. 

Replace the front end cap cover. Screw the cover on until metal 
contacts metal. Do not over-tighten the cover. 

Содержание FloBoss 103











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды