manualshive.com logo in svg

Emerson Fisher 4660, Инструкция по эксплуатации

Поделиться
Скачать
Emerson Fisher 4660 Скачать руководство пользователя страница 2

Instruction Manual

D200163X012

4660 Pressure Pilot

June 2017

2

Introduction

Scope of Manual

This instruction manual provides installation, operating, maintenance, and parts ordering information for the Fisher
4660 high‐low pressure pilot. Refer to separate instruction manuals for information regarding the control valve
actuator.

Do not install, operate, or maintain a 4660 pressure pilot without being fully trained and qualified in valve, actuator,
and accessory installation, operation and maintenance.

 To avoid personal injury or property damage it is important to

carefully read, understand, and follow all of the contents of this manual, including all safety cautions and warnings.

 If

you have any questions about these instructions, contact your 

Emerson sales office

 or Local Business Partner.

Description

The 4660 high‐low pressure pilot (figure 1) activates emergency shutdown systems for flowlines, production vessels,
and compressors. The pilot can be used with either a single or dual set point capability to maintain full output pressure
when the process is operating within the set point range. The primary switching mechanism in this pilot is a
block‐and‐bleed relay assembly.

Unless otherwise noted, all NACE references are to NACE MR0175‐2002.

Specifications

Specifications for the 4660 high‐low pressure pilot are listed in table 1.

Educational Services

For information on available courses for the 4660 high‐low pressure pilot, as well as a variety of other products,
contact:

Emerson Automation Solutions
Educational Services - Registration
Phone: 1-641-754-3771 or 1-800-338-8158
E-mail: [email protected]
emerson.com/fishervalvetraining

Содержание Fisher 4660

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды