background image

3

EMERSON QUICK START GUIDE

The Quick Start Guide covers the installation
instructions common for ceiling fan operations. If
additional assistance with wiring, alternate hanging
systems, or lighting options, proceed to the complete
instructions of this Owner’s Manual.

The Quick Start Guide sections include page numbers
to correspond with the appropriate sections of the
Owner’s Manual for detailed instructions.

*

See Unpacking Instructions for a complete list of
parts for installation. 

Installation of Downrod (page 76)

1.

Remove the hanger ball from
the downrod.

2.

Install the downrod to the
motor coupling using the
clevis pin and hairpin clip.

3.

Tighten the setscrews.

1.

Disconnect electrical power to
the branch circuit at the
circuit breaker or fuse box
before attempting to install
the ceiling fan hanger bracket
on the outlet box.

CEILING

FLOOR

AT LEAST

7'

2.

The fan must be hung with at
least 7’ of clearance from
floor to blades.

3.

Attach the hanger bracket to
the outlet box.

4.

Seat the hanger ball/downrod
assembly on the hanger
bracket.

Hanging Your Ceiling Fan (page 10)

To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for Fan
Support”, and use screws supplied with outlet box. Most
outlet boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.

!

WARNING

Installation of Blade Assembly (page 8) 

1.

Turn fan assembly upside
down in preparation for
mounting fan blade
assemblies.

2.

To ensure proper blade
assembly, make sure the label
on the blades are facing the
bottom of the ceiling fan.
Slide blade through center
slot in fan housing. Mount
blade to fan housing using
three 3/16-24 x 1/2” slotted
Phillips washer head blade
screws.

Installation of Switch Housing (page 8)

1.

Remove two of the four
screws in the motor assembly
and loosen the remaining two
screws.

2.

Connect the terminals of the
lower housing assembly to
the terminals of the fan motor
assembly.

Installation of Ceiling Fan (page 8)

1.

Remove the three screws pre-
installed on top of the fan
assembly. Install the coupler
cover and ceiling cover onto
the downrod. Reinstall the
three screws through the
coupler cover. 

2.

Reinstall the hanger ball onto
the downrod, place the pin
into the hanger ball and
tighten the setscrew.

Turning off wall switch is not sufficient. To avoid possible electrical
shock, be sure electricity is turned off at the main fuse or circuit
breaker box before wiring. All wiring must be in accordance with
National and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical shock.

!

WARNING

ETL Model No.: CF955-3

Содержание CF955BS 03





















Отзывы: