background image

8

How to Put Your Ceiling Fan Together 

(continued)

7.

Reinstall the hanger ball (Figure 4) on the downrod
as follows. Route the motor leads through the
downrod. Position the pin through the two holes in
the downrod and align the ball so the pin is captured
in the groove in the top of the hanger ball. Pull the
hanger ball up tight against the pin and securely
tighten the setscrew in the hanger ball. A loose
setscrew could create fan wobble.

It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.

WARNING

!

Il est crucial que l'axe dans le cylindre de suspension
soit installé correctement et que la vis de blocage soit
bien serrée. Si vous ne vous assurez pas que l'axe et la
vis sont installés correctement, le ventilateur risquerait
de tomber.

AVERTISSEMENT 

!

CEILING COVER

DOWNROD

PIN

SETSCREW

HANGER
BALL

Figure 4

MOTOR
HUB

3/16-24 x 1/2" SLOTTED
PHILLIPS WASHER HEAD
BLADE SCREWS

FAN BLADE

BLADE SLOT
IN HOUSING

LABEL
(LOCATED ON
BOTTOM OF BLADE)

Figure 5

TERMINALS

LOWER 
HOUSING
ASSEMBLY

FAN MOTOR
ASSEMBLY

REMOVE 
2 SCREWS

LOOSEN 
2 SCREWS

FUSE AND 
FUSE HOLDER

Figure 6

8.

The fan comes with black and white leads that
are 80” long. Before installing fan, measure up
approximately 6 to 9-inches above top of hanger
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.

9.

Turn fan assembly upside down in preparation for
mounting fan blades.

10.

To ensure proper blade assembly, make sure the
label on the blades are facing the bottom of the
ceiling fan. Slide blade through center slot in fan
housing. Mount blades to fan housing using three 
3/16-24 x 1/2” slotted Phillips washer head blade
screws on each blade (Figure 5).

NOTE: Take care not to scratch fan housing when
installing blades.

11.

Remove two of the four screws in the motor
assembly and loosen the remaining two screws
(Figure 6).

12.

Connect the terminals of the lower housing
assembly to the terminals of the fan motor
assembly (Figure 6).

ETL Model No.: CF955-3

Содержание CF955BS 03





















Отзывы: