manualshive.com logo in svg

Emerson Bettis EHO, Инструкция по установке и эксплуатации

Поделиться
Скачать
Emerson Bettis EHO Скачать руководство пользователя страница 34

Installation and Operation Manual

Part Number: VA001-507-32, Rev. 1

August 2016

31

Section 4: Set-up/Start-up Procedure

Set-up/Start-up Procedure

4.8.2  Double Acting Actuator with an (Optional) ESD Solenoid Valve and Accumulator 

Figure 21 

2-Way Remote Electric Without an ESD Solenoid Function Schematic 

(M) 

Hand Pump Selection Valves

(L) 

Hand Pump

(J) 

Opening Solenoid

(K) 

Closing Solenoid

K

J

L

M

I

M

NOTE:  

The components referenced below are referencing Schematic 4.8.2. and is for 
illustration purposes only. When using this procedure refer to the Bettis EHO Actuator 
General Arrangement Drawing and Hydraulic Schematic for the unit being worked on.

4.8.2.1  Ensure both Hand Pump Selection Valves (M) are in the automatic 

open position.

4.8.2.2  ESD (Emergency Shut Down) Solenoid Valve (P)is constantly energized 

closed.

4.8.2.3  Ensure Isolation Valve (H) is closed and Isolation Valves (N) and (O) are 

both open.

4.8.2.4  Push and release the OPEN/CLOSE PUSHBUTTON to start the Electric 

Motor. The Hydraulic Pump Draws Fluid from the Reservoir and 
discharges fluid to the nitrogen pre-charged accumulator.

Содержание Bettis EHO




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды