manualshive.com logo in svg

Emerson Bettis EHO, Инструкция по установке и эксплуатации

Поделиться
Скачать
Emerson Bettis EHO Скачать руководство пользователя страница 29

August 2016

Installation and Operation Manual

Part Number: VA001-507-32, Rev. 1

26

Section 4: Set-up/Start-up Procedure

Set-up/Start-up Procedure

4.5.1 

Rotate both Hand Pump Isolation Valves (O) to the downward horizontal 
position.

4.5.2  Select and push inward the open or close knob located on the Hand Pump 

Selector Manifold (L).

4.5.3  Use supplied Hand Pump Handle to discharge hydraulic fluid into the open or 

close side of the actuator cylinder.

4.5.4  Once the actuator is fully stroked and makes contact with the actuators 

adjustable stops, observe if any leakage is detected at any tube fittings or port 
connections from the Hand Pump to the Actuators operating ports.

4.5.5  Push the Pump By-Pass Valve located on the top of the Hand Pump Selector 

Manifold (L) and pull the pump handle downward retracting the pump ram into 
the pump body.

4.5.6  Select and push inward the opposite open or close knob located on the Hand 

Pump Selector Manifold (L).

4.5.7  Repeat steps 4.5.3 thru 4.5.5
4.5.8  Rotate both Hand Pump Selector Valves (M) back into the upward vertical 

position.

4.6 

Check Rotation

NOTE:  

The components referenced below are referencing to schematic found in section 10.2. 
and is for illustration purposes only. When using this procedure refer to the Bettis EHO 
Actuator General Arrangement Drawing and Hydraulic Schematic for the unit being 
worked on.

4.6.1 

Turn on the electrical supply to the unit. If an ((optional)) Circuit Breaker Module 
is supplied, turn the Circuit Breaker to ON.

4.6.2  Turn the LOCAL-OFF-REMOTE selector switch to LOCAL.
4.6.3  Ensure Flow Control Valves (V) are adjusted fully counterclockwise for maximum 

flow.

4.6.4  Open inspection port on side of unit to observe the rotation of the motor/pump 

shaft.

Figure 18 

Inspection Port for Motor Rotation

Содержание Bettis EHO




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды