manualshive.com logo in svg

Emerson Bettis EHO, Инструкция по установке и эксплуатации

Поделиться
Скачать
Emerson Bettis EHO Скачать руководство пользователя страница 10

7

Installation and Operation Manual

Part Number: VA001-507-32, Rev. 1

August 2016

Section 2: Installation

Installation

2.4.1.2 

Horizontal Pipeline Horizontal Stem 

The small G-Series and all E-Series actuators mounting on a horizontal 
pipeline with a horizontal valve stem should be supported on 
the ends of the drive module. A strap may be attached to the 
stabilization tab on the spring module to balance the unit while 
lifting. The weight of the actuator must be supported at the drive 
module, not the stabilization tab. See Figure 2.

Figure 2 

G01 – G3 and all E-Series Actuators with Horizontal  

 

 

Pipeline and Horizontal Stem

2.4.2  G3-Series Actuators

2.4.2.1 

Horizontal Pipeline Vertical Stem 

The G3-Series actuator mounting on a horizontal pipeline with a 
vertical valve stem should be supported at the ends of the drive 
module. A strap may be attached to the stabilization tab on the spring 
module to balance the unit while lifting. The weight of the actuator 
must be supported at the drive module, not the stabilization tab. See 
Figure 3.

Figure 3 

G3 with a Horizontal Pipeline and Vertical Stem

 CAUTION: 

Never lift the actuator with a valve attached. Always handle actuator/valve assemblies 
by attaching lifting equipment to the valve only.

Содержание Bettis EHO




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды