manualshive.com logo in svg

Emerson Bettis EHO, Инструкция по установке и эксплуатации

Поделиться
Скачать
Emerson Bettis EHO Скачать руководство пользователя страница 30

Installation and Operation Manual

Part Number: VA001-507-32, Rev. 1

August 2016

27

Section 4: Set-up/Start-up Procedure

Set-up/Start-up Procedure

4.6.5  While observing the inspection port, for motor rotation, push and release the  

OPEN/CLOSE PUSHBUTTON to Power Stroke the actuator and immediately push 
the STOP Pushbutton. Motor rotation should be counterclockwise when looking 
at the back of the motor.

4.6.6  If needed, correct motor rotation.

NOTE:  

If the EHO Actuator is supplied with optional ESD, before operating a motor-powered 
stroke, a customer supplied ESD signal must be present and Solenoid Valve (P) 
energized.

4.6.7  Push and release the OPEN/CLOSE PUSHBUTTON to Power Stroke the actuator. 

The Electric Motor (Z) will start to run driving Hydraulic Pump (Y). The 
Hydraulic Pump (Y) draws fluid from Reservoir (I) and pushes it into the Bettis 
G-series hydraulic cylinder (W). 

4.6.8  Shut off the electrical power going to the unit, if an (optional) Circuit Breaker 

Module is supplied, turn the Circuit Breaker to OFF.

4.7 

Limit Switch Adjustment

4.7.1 

To complete limit switch adjustment, the actuator will need to be stroked from 
a fully closed position to a fully open position etc. several times. In the following 
instructions, the electric motor is used to Power Stroke the actuator. If it is not 
safe or possible to use the electric motor at this time, use the Hand pump to 
Power Stroke the actuator.

4.7.2 

The limit switch adjustments are found in a covered compartment in line with 
the valve stem and on the opposite side of the control box. Remove the limit 
switch compartment cover by loosening the four corner bolts retaining it. 
All covers have tapped holes for jackscrews to aid in removing the cover. Use 
the retaining screws in these holes to lift the cover evenly at each corner. Use 
caution to not allow the cover to bind during removal.

Figure 19 

Remove Cover for Limit Switch Chamber

Содержание Bettis EHO




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды