manualshive.com logo in svg

Emerson Bettis EHO, Инструкция по установке и эксплуатации

Поделиться
Скачать
Emerson Bettis EHO Скачать руководство пользователя страница 33

August 2016

Installation and Operation Manual

Part Number: VA001-507-32, Rev. 1

30

Section 4: Set-up/Start-up Procedure

Set-up/Start-up Procedure

4.8 

Function Test

4.8.1 

Double Acting Actuator without an ESD Solenoid Valve 

NOTE:  

The components referenced below are referencing Schematic 4.8.1. and is for 
illustration purposes only. When using this procedure refer to the Bettis EHO Actuator 
General Arrangement Drawing and Hydraulic Schematic for the unit being worked on.

4.8.1.1  Ensure both Hand Pump Selector Valves (M) are in the automatic open 

position.

4.8.1.2  Energize the desired solenoid valve (J) to open the actuator or (K) to 

close the actuator.

4.8.1.3  Push and release the OPEN/CLOSE PUSHBUTTON to start the Electric 

Motor. The Hydraulic Pump Draws Fluid from the Reservoir and 
discharges fluid thru either the opening solenoid (J) or the closing 
solenoid (K) which ever one is energized.

4.8.1.4  Upon completion of the open or close stroke, the Pressure Switch will 

reach its set point and stop the Electric Motor.

4.8.1.5  Upon completion of the open or close stroke, the Limit Switch(s) 

can be configured to de-energized the solenoid that is energized. 
Some field installations can use the customer’s control room logic to 
de-energize the solenoids after the actuator stroke open or close is 
reached.

Содержание Bettis EHO




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды