Emerson Bettis CL-05 Скачать руководство пользователя страница 49

Страница: 49 / 91

User Instructions

MAN-02-04-60-0350-EN Rev. 3

February 2019

Section 7: Parameter Menu

Parameter Menu

Table 11.

Binary Inputs Parameter Group (1)

Menu

Item

Sub Menu
Item

Poss. Setting

Notes / Comments

P9.1

Binary
Input

Input 1

0:no function

This input has no function

1: Open

OPEN command in REMOTE mode (selector switch in
position REMOTE).

2: Closed

CLOSED command in REMOTE mode (selector switch in
position REMOTE).

3: Stop

STOP command in REMOTE mode (selector switch in
position REMOTE).

4: Open Self-hold

Self-hold for OPEN, i.e., a short pulse is sufficient and the

actuator moves then into the end position. Use the STOP
command to stop the actuator.

5: Closed Self hold Self-hold for CLOSED, see OPEN SELF-HOLD

6: Emergency
Open

Superimposed run command; run the actuator in direction
OPEN regardless of whether the selection switch is set to
REMOTE or LOCAL operation

7: Emergency
Closed

Superimposed run command; run the actuator in direction
CLOSED regardless of whether the selection switch is set to
REMOTE or LOCAL

8: Release

The actuator may be operated only with a switched signal.
Both in local and remote operation

9: Open/Closed

The actuator moves towards OPEN if input is active and
towards CLOSED otherwise

10: Close/Open

The actuator moves towards CLOSED if input is active and
towards OPEN otherwise

11: Positioner

Release of the postioner

12: Open inv.

As open but active low

13: Close inv.

As CLOSED but active low

14: Stop inv.

As STOP but active low

15: Open
Self-Hold inv.

As Open Self-Hold but active low

16: Closed
Self-Hold inv.

As Closed Self-Hold but active low

17: Emergency-
Open inv.

As Emergency-Open but active low

18: Emergency-
Closed inv.

As Emergency-Closed but active low

19: Block

With activated (switched) signal, the actuator is locked for
operation also in local mode

20: Contoller lock Positioner lock

21: Release Local The actuator may be operated only with a switched signal.

22: Block Local

As Release Local but active low

23: Lock Open

Trigger lock OPEN (in LOCAL and REMOTE mode).
Actuator moves with the highest priority to OPEN;
command continues internally active after reaching the
end position OPEN. Dropping only with LOCK OFF, Supply
OFF or operating mode OFF.

Содержание Bettis CL-05




























































































Результаты поиска

Содержание Bettis CL-05

Отзывы:

Похожие инструкции для Bettis CL-05

Бренды по названию

Популярные бренды

Emerson Bettis CL-05, Инструкция пользователя

Результаты поиска

Содержание Bettis CL-05

Отзывы:

Похожие инструкции для Bettis CL-05

Бренды по названию

Популярные бренды