Emerson Bettis CL-05 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 91

background image

February 2019

User Instructions

MAN-02-04-60-0350-EN Rev. 3

49

Section 7: Parameter Menu

Parameter Menu

CAUTION: NOTE SET TORQUE AND POSITION

When using the point torque-dependent OPEN or torque-dependent CLOSED (see Section
7.1, Menu P1.3 u. P1.4) the actuator will only be open or closed when the set torque and
the associated end position is reached. If the end position is not reached, a torque error is
reported (see Section 6.2.2)

7.10

Parameter Group: Position Output (option)

Position output is used to indicate the current position of the actuator using 0/4-20 mA; it

can retrofitted using software code.

If this option is not enabled, the menu point shows the message "inactive".

No adjustment to the end positions or the travel is required. Adjustment is automatically

performed during the configuration of travel limit positions (see Section 7.1)

No further settings are necessary for torque-dependent switch off, because the controller
exclusively uses travel limit posi- tions for the calculation. Regardless of whether this is

defined by the torque or the travel limit positions.

The factory default setting is:

4mA at 0% position

20mA at 100% position

Table 16.

Position Output Parameter Group (1)

Menu item

Sub Menu
Item

Poss.
Setting

Notes / Comments

P11.1

PositionOutput

Function

0: off

mA output disabled

1: Position mA output corresponds to the actual position value
2: Pos.
Valvechar

mA output corresponds to the actual position value
taking into account the valve characteristic.

3: Torque 1

mA output corresponds to the actual torque value
torque = 100% Close: mAoutput = start
torque = 0%: mAoutput = center
torque = 100% Open: mAoutput = end

4: Torqe 2

mAoutput corresponds to the actual torque value
torque = 100% Close: mAoutput = end
torque = 0%: mAoutput = start
torque = 100% Open: mAoutput = end

5: Torque 3

mAoutput corresponds to the actual torque value
torque = 150% Close: mAoutput = start
torque = 0%: mAoutput = center
torque = 150% Open: mAoutput = end

6: Torque 4

mAoutput corresponds to the actual torque value
torque = 150% Close: mAoutput = end
torque = 0%: mAoutput = start
torque = 150% Open: mAoutput = end

«
...
52
53
54
55
56
...
»

Содержание Bettis CL-05




























































































Отзывы:

Нет отзывов

Похожие инструкции для Bettis CL-05

Бренд: Valve Concepts Страницы: 16

Бренд: Echelon Страницы: 40

Бренд: Garmin Страницы: 12

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 22

Бренд: Eaton Страницы: 10

Бренд: Idemia Страницы: 29

CentriPro Aquavar SOLO

Бренд: Xylem Страницы: 48

Q Module WFZ16.Ox

Бренд: QUNDIS Страницы: 24

Бренд: FUTABA Страницы: 8

Бренд: DAQ Страницы: 63

SAE 07.2 Series

Бренд: AUMA Страницы: 116

Бренд: IFM Страницы: 41

Бренд: Duco Страницы: 16

Бренд: U-Tron Страницы: 8

Бренд: Agilent Technologies Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды