Emerson 1F95-1280, Инструкция по установке и эксплуатации

Страница: 5 / 16

INSTALLER/CONFIGURATION MENU
To enter the menu: Press the Menu touch key . Press and hold for 5 seconds the Installer Config touch key . This displays
screen reference #1 in the table below . Screen Reference numbers appear in top right corner of display . Press to advance
to the next menu item or to return to a previous menu item . Press or to change a menu item option . Shaded items are
not available if selected for Non-Programmable .
CONFIGURATION MENU
Screen
Reference
Number
SS1
MS2
HP1
HP2 Press
key
Displayed
Factory
(Default)
Press or
to select from
listed options
Comments
1   MS 2 HP 1, HP 2, SS 1 Selects Multi-Stage (MS2, No Heat Pump), Heat Pump 1
(HP1, 1 compressor), Heat Pump 2 (HP2, 2 compressor
or 2 speed compressor), or Single Stage .
2   (GAS) ELE GAS setting: furnace controls blower .
ELE setting: thermostat controls blower .
3

0b (0) b Selects Reversing Valve (This item is only to appear if HP1 or HP2
is selected above .)
4   Days, (7) P 5 or 0 Programs per week . (7 days, 5-1-1 days or non-programmable)
5

Cool-Off-
Heat-Auto
Cool-Off-Heat, Heat Off,
Heat, Cool-Off, Auto Off
System switch configuration in non heat pump mode .
 Cool-Off-Heat-
Em-Auto
Cool-Off-Heat-Em,
Off-Em-Auto
System switch configuration, heat pump mode .
6   (On)
E OFF
Selects Energy Management Recovery . Not available if 4 is 0
7   (FA) Heat, Cr SL Selects Adjustable Anticipation, cycle rate, Heat
8
 
(FA) Cool, Cr SL Selects Adjustable Anticipation, cycle rate, Cool
9  (FA) Cr/AU, Em SL Selects Adjustable Anticipation, cycle rate auxiliary, (This item is
only to appear if HP1 or HP2 is selected above) .
10
 
(OFF) CL On Selects Compressor Lockout .
11   (On)
dL
OFF Selects Continuous Display backlight .
12   (LO) dL HI Selects Backlight Intensity .
13   0
(Temperature)
5, LO to 5, HI Selects Adjustable Ambient Temperature Display [range -5 (LO) to
+5 (HI)] .
14
 
°F °C Selects °F/°C Display (temperature units in Fahrenheit or Celsius) .
15   (On)
b
OFF Selects audible Beeper On/Off .
16   (On) dS OFF Selects Daylight Saving Time calculation .
17
 
(On) Heat, AS OFF Selects Automatic Schedule for comfort temperature Programming,
heat mode . Not available if 4 is 0
18   (On) Cool, AS OFF Selects Automatic Schedule for comfort temperature Programming,
cool mode . Not available if 4 is 0
19   (OFF)
CS
On Selects Cool Savings Feature On of Off .
20   CS Cool Savings
(3)
1-2-3-4-5-6 Selects amount of Cool Savings adjustment .
21   (OFF)
CO
On Selects Compressor Optimization (not available on earlier models)
22   (99) Heat, HL 62-98 TEMPERATURE LIMIT, HEAT (max . heat set point) .
23   (45) Cool, LL 46-82 TEMPERATURE LIMIT, COOL (min . cool set point) .
24
 
OFF,
Keypad Lockout
L (total), P (partial),
Temperature Limit
(limited temperature range)
Selects Keypad Lockout .
25   000 001-999 Selects Keypad Lockout Combination (active only if keypad Lockout
is selected) .
26 MS2  (On) Heat, FS OFF Fast second stage of heat (not available if SS1 is selected above) .
27 MS2 HP2 (On) Cool, FS OFF Fast second stage of cool (not available if SS1 or HP1
is selected above) .
28   Remote (OFF) On Remote temperature sensor, enable/disable .
29   Remote, In Outdoor Remote Remote temperature sensor (Indoor/Outdoor) .
30   (On) LS OFF Local temp . Sensor enable/disable (only when Indoor Remote is
selected On) .
31  (OFF) dF On Selects Dual Fuel feature On or OFF (this item appears if HP1 or HP2
is selected above) .
32

(35) dF -5 - 50 Selects Dual Fuel setpoint (°F), dF selected On with outdoor sensor
available .
33  (05) dF 0 - 09 Selects Dual Fuel setting using software logic, dF selected On with no
outdoor sensor .
5