EMBRON Hatteland HD 19T22, Руководство пользователя

Страница: 124 / 142

Pinout Assignments
124
IND100241-31
Appendix
20-pin DisplayPort (DP) Female
20 18 16 14 12 10 8 6 4 2
19 17 15 13 11 9 7 5 3 1
PIN 01 ML_Lane 0 (p) - Lane 0 (positive)
PIN 02 GND - Ground
PIN 03 ML_Lane 0 (n) - Lane 0 (negative)
PIN 04 ML_Lane 1 (p) - Lane 1 (positive)
PIN 05 GND - Ground
PIN 06 ML_Lane 1 (n) - Lane 1 (negative)
PIN 07 ML_Lane 2 (p) - Lane 2 (positive)
PIN 08 GND - Ground
PIN 09 ML_Lane 2 (n) - Lane 2 (negative)
PIN 10 ML_Lane 3 (p) - Lane 3 (positive)
PIN 11 GND - Ground
PIN 12 ML_Lane 3 (n) - Lane 3 (negative)
PIN 13* CONFIG1 - connected to Ground*
PIN 14* CONFIG2 - connected to Ground*
PIN 15 AUX CH (p) - Auxiliary Channel (positive)
PIN 16 GND - Ground
PIN 17 AUX CH (n) - Auxiliary Channel (negative)
PIN 18 Hot Plug - Hot Plug Detect
PIN 19 Return - Return for Power
PIN 20 DP_PWR - Power for connector (3.3 V 500 mA)
*Pins 13 and 14 may either be directly connected to ground or
connected to ground through a pulldown device. This is the pinout for
source-side connector, the sink-side connector pinout will have lanes
0–3 reversed in order; i.e., lane 3 will be on pin 1(n) and 3(p) while
lane 0 will be on pin 10(n) and 12(p).
10+10 pin Isolated Digital Input/Output Module
Type Number “PCA100297-1”
Module A Module B
Module A Module B
A1 External Power + A1 IN+[0]
A2 N/C (Not Connected) A2 IN-[0]
B1 External Power - (GND1) B1 IN+[1]
B2 N/C (Not Connected) B2 IN-[1]
O1 HS[0] O1 N/C
C1 HS[1] C1 IN+[2]
C2 N/C (Not Connected) C2 IN-[2]
D1 HS[2] D1 IN+[3]
D2 N/C (Not Connected) D2 IN-[3]
O2 HS[3] O2 N/C
9-pin Amplifi ed Mono/Stereo Audio Out, DSUB Female
Type Number “HT 00235 OPT-A1”
5 4 3 2 1
9 8 7 6
PIN 01 LAUDR Left Audio Return*
PIN 02 LAUD Left Audio*
PIN 03 RAUDR Right Audio Return
PIN 04 RAUD Right Audio
PIN 05 N/C No internal connection
PIN 06 N/C No internal connection
PIN 07 N/C No internal connection
PIN 08 N/C No internal connection
PIN 09 N/C No internal connection
*For Mono: connect pin 01 and 02 only
10+10 pin RS-422 / RS-485 NMEA Module
Type Number “PCA200828-1 / PCA100293-1”
6 7 8 9 10
1 2 3 4 5
6 7 8 9 10
1 2 3 4 5
PIN 01 TxD- Transmit Data Negative
PIN 02 TxD+ Transmit Data Positive
PIN 03 GND Isolated Ground
PIN 04 RxD- Receive Data Negative
PIN 05 RxD+ Receive Data Positive
PIN 06 TxD- Transmit Data Negative
PIN 07 TxD+ Transmit Data Positive
PIN 08 GND Isolated Ground
PIN 09 RxD- Receive Data Negative
PIN 10 RxD+ Receive Data Positive
RS-485 Half Duplex (2-wire) Confi guration:
Connect TX and RX pair-wise:
TX- to RX-, TX+ to RX+.
*Note: The jumper for “force of transmitter
(Forced TX(y)” is open by factory default. For
some custom models this jumper is preset
to closed (active), in that case unit has to be
opened and jumper set to open to allow Half
Duplex mode.
8-pin RJ-45 10/100Mbps LAN/Ethernet
PCA100298-1 / HT 00274 OPT-A1
1 2 3 4 5 6 7 8
Pin 01 - TDP Transmit Diff erential Pair (Positive)
Pin 02 - TDN Transmit Diff erential Pair (Negative)
Pin 03 - RDP Receive Diff erential Pair (Positive)
Pin 04 - NC Not Connected
Pin 05 - NC Not Connected
Pin 06 - RDN Receive Diff erential Pair (Negative)
Pin 07 - NC Not Connected
Pin 08 - NC Not Connected