EMBRON Hatteland E Series, Руководство пользователя

Страница: 91 / 136

Pinout Assignments
91
IND100241-37
Appendix
Serial Communication settings configured in BIOS: “Advanced/F81964 Super IO Configuration/Serial Port 4 Configuration/”
COM Port is identified in (Windows 10) Operating System as “COM4:”
Termination:
“On” or “Off” supported.
Flow Control: Selectable in BIOS “Change Settings”:
“Send by RTS” or “Auto RTS” (Automatically, no action needed by user application.)
“RS485 RTS# Auto Flow Control:” Disabled/Enabled
9-pin non-isolated Serial COM DSUB Male
RS-232
1 2 3 4 5
6 7 8 9
PIN 01 - Do not connect
PIN 02 RxD Receive Data
PIN 03 TxD Transmit Data
PIN 04 - Do not connect
PIN 05 GND Signal Ground
PIN 06 N/C No internal connnection
PIN 07 N/C No internal connnection
PIN 08 N/C No internal connnection
PIN 09 N/C No internal connnection
Total 3 pins required.
Pin 1
Pin 3
Pin 5
Pin 2
To External Peripheral 9-pin DSUB Female Add
Note Orientation! Backshell
Cable
9-pin non-isolated Serial COM DSUB MALE
RS-485 HALF DUPLEX
1 2 3 4 5
6 7 8 9
PIN 01 Data - Data Negative
PIN 02 Data + Data Positive
PIN 03 - Do not connect
PIN 04 - Do not connect
PIN 05 GND Signal Ground
PIN 06 N/C No internal connnection
PIN 07 N/C No internal connnection
PIN 08 N/C No internal connnection
PIN 09 N/C No internal connnection
Total 3 pins required.
Pin 1
Pin 2
Pin 5
Pin 1
To External Peripheral 9-pin DSUB Female Add
Note Orientation! Backshell
Cable
9-pin non-isolated Serial COM DSUB MALE
RS-422 / RS-485 FULL DUPLEX
1 2 3 4 5
6 7 8 9
PIN 01 TxD- (Z) Transmit Data Negative
PIN 02 TxD + (Y) Transmit Data Positive
PIN 03 RxD + (A) Receive Data Positive
PIN 04 RxD - (B) Receive Data Positive
PIN 05 GND Signal Ground
PIN 06 N/C No internal connnection
PIN 07 N/C No internal connnection
PIN 08 N/C No internal connnection
PIN 09 N/C No internal connnection
Total 5 pins required.
Pin 1
Pin 2
Pin 5
Pin 1
To External Peripheral 9-pin DSUB Female Add
Note Orientation! Backshell
Pin 3
Pin 4
Cable
Building your own cable:
Note: Requires soldering and assembly. It is expected that the technician has experience in electronics, soldering and assembling cables and connectors.
Use a cable that contains at least the wires required (not single wires). Heat Shrink Tubes must be applied to soldered wire/pins. Test connection (beep) with
Voltage Meter. Test connection between power pin and other pins to ensure no short circuit is present prior to connecting cable and power on Display unit.
Finally, the 9-pin DSUB must be covered by a back shell.
RS-422 / RS-485 FULL DULEX
120Ω
DE (Data Enable)
External Device
Termination Ω
at end of cable
External Device
TX
TX
RX
RX
120Ω
Termination Ω
at end of cable
120Ω
120Ω
Termination Ω
at end of cable
Termination Ω
at end of cable
TX
External Device
TX
External Device
RX RX
Pin 1: TxD- (Z)
Pin 2: TxD+ (Y)
Pin 3: RxD+ (A)
Pin 4: RxD- (B)
1 1
1
2 2
2
4
4
4
3
3
3
*
RS-485 HALF DULEX
120Ω
Pin 1: Data-
Pin 2: Data+
External Device
120Ω
Termination Ω
at end of cable
Termination Ω
at end of cable
External Device
DE (Data Enable) DE (Data Enable)
Note: 120Ω termination on TX pins are rarely needed, unless cable is long or enviroment is very noisy.
*