EMAK SPL 910 PTO, Руководство по эксплуатации и техническому обслуживанию

Страница: 28 / 60

28
D22001956 - v.0 - UPD 020210
5.1.C - Switching on/off of the tractor-driven log splitter (SPL 910 PTO)
WARNING
Use CE-marked cardan shaft only. Carefully follow the manufacturer operating instructions
•
Connect the log splitter to the power source (see chapter 4 “OPERATING THE MACHINE FOR THE FIRST TIME”) and then check that the machine
is firmly positioned on the ground.
•
Start the tractor making sure it does not move. Start the log splitter by activating the power system (cardan shaft). The wedge will lift.
•
Use the log splitter as explained in paragraph 5.2.
•
If you leave the log splitter unattended, switch off the transmission system of the tractor.
•
After using the log splitter, switch off the transmission system and disconnect the machine from the power source.
Before moving the tractor, lift the log splitter to a sufficient height so that it does not hit the ground.
WARNING
Never move the tractor with the power source of the log splitter activated or with the log splitter still on the ground.
5.2 - How to use log splitter
•
Place the log on the work surface (6 in fig.1, page 2) making sure it is centered under the wedge. The two faces of the log must be parallel to each
other and to the work surface to guarantee safe operation.
•
Working in the mandatory position only (14 in fig.1 page 2), activate both the levers downwards (vertical position - B in fig.5, page 2) or ahead
(horizontal position - B in fig.10, page 5): the wedge will start to cut into the log.
•
Once splitted the log, the pieces will not fall down, because they will be kept by the side arms.
•
If the log does not split quickly or if the wedge stops, do not keep the machine under force.It is advisable to bring the wedge to the upper position
and to make another attempt after rotating the log.
•
Repeat the operation with the pieces obtained so as to split the log into several parts.
IN ORDER TO SPLIT SHORT LOGS USE THE
MOVABLE TABLE (FIG.13, PAGE 6)
•
In order to let the wedge return to the upper position, ready for a new cycle, push both levers upward until the clamp. The two levers will stay
in this position. At the end of the stroke, the stopping device will automatically bring them back to the neutral position.
Note: If you release also only one of the two control levers, the wedge will stop in the reached position.
WARNING
THE MANUFACTURER IS NOT LIABLE FOR INJURY TO PERSONS, ANIMALS OR OTHER THINGS CAUSED BY AN IMPROPER USE OF
THE MACHINE
5.3 - Use of the movable table (Optional)
The log splitter can be equipped, under request, with an optional movable table (fig.13, page 6) that allows to split shorter logs.
The movable table (A in fig.13) must be positioned on the work surface and locked with the security pin (B in fig.13) paying attention to insert it
completely and fixing it with the ‘R’ shaped security pin.
If the movable table is to be used, the wedge must do only the necessary stroke to arrive to the table without damaging it.
WARNING
Never operate the machine if the dowel is not fully inserted or if it is not locked with the ‘R’ shaped security pin.
5.4 - Closing the cylinder for transport
Before lifting and moving the log splitter, the cylinder must be lowered as follows:
•
Position a piece of wood under the wedge, on the work surface (A in fig.5, page 2) and remove the "R" shaped security pin from the cylinder
check pins (C in fig.6a, page 3)
•
Activate both the control levers (B in fig.5, page 2) in order to lower the wedge completely.
•
Release the right lever (B in fig.6a) in order to hold the wedge in the reached position.
•
Remove the cylinder check pins (C in fig.6a) and put them in the appropriate places on the two sides of the cylinder (fig.6c).
•
Release also the left lever, therefore activate both the control levers upwards until they clamp, in order to close the cylinder
•
When the cylinder is completely closed and the wedge raised from the piece of wood, bring the levers back to the neutral position.
•
Insert the cylinder check pins in the appropriate places for the transport and fix them with the "R" shaped security pin (fig.6d, page 3)
Now the log splitter can be lifted, moved and transported
WARNING
NEVER MOVE THE LOG SPLITTER WHEN THE CYLINDER IS LIFTED. THE MANUFACTURER IS NOT LIABLE FOR INJURY TO PERSONS,
ANIMALS OR OTHER THINGS CAUSED BY TRANSPORTING THE LOG SPLITTER WITH THE CYLINDER LIFTED.
ENGLISH