ELTRA ELEMENTRAC CS-i Скачать руководство пользователя страница 37

Страница: 37 / 86

Maintenance

10.1.3

Filling reagent tubes

CAUTION

C24.0000

Risk of injury

Pressurised system

−

The machine is pressurised during operation. The removal of the reagent

tube during operation results in an explosive escape of chemicals or
sample material and can cause injuries.

•

Never remove reagent tubes during operation.

CAUTION

C25.0076

Risk of burns

Hot machine parts

−

Some parts of the machine can get very hot and cause burns when

touched without wearing protective gloves.

•

Wear heat-resistant protective gloves when working with hot
machine parts.

•

Never touch hot parts of the machine without suitable protective
gloves.

CAUTION

C26.0090

Risk of eye injury

Chemicals

−

When changing the chemicals, minute particles of chemicals may be

suspended in the air and cause burns to eyes.

•

Always wear protective goggles when working with chemicals.

•

Comply with the safety data sheets for the chemicals used.

WARNING

W18.0000

Risk of poisoning

Toxic combustion gases

−

Samples are exposed to high temperatures during the analysis. Harmful

gaseous fission products can be released or formed from reaction
processes here. These gases can escape from the gas outlet and cause
serious poisoning.

•

Connect the exhaust air outlet on the machine to a suitable
ventilation system.

•

Wear your personal protective equipment.

•

Comply with the safety data sheet for the substances used.

•

Carry out a risk analysis on the potential hazards of your samples
and implement protective measures.

Содержание ELEMENTRAC CS-i























































































Результаты поиска

Содержание ELEMENTRAC CS-i

Отзывы:

Похожие инструкции для ELEMENTRAC CS-i

Бренды по названию

Популярные бренды

ELTRA ELEMENTRAC CS-i, Руководство по эксплуатации

Результаты поиска

Содержание ELEMENTRAC CS-i

Отзывы:

Похожие инструкции для ELEMENTRAC CS-i

Бренды по названию

Популярные бренды