ELTRA ELEMENTRAC CS-i Скачать руководство пользователя страница 15

Страница: 15 / 86

Safety

CAUTION

C4.0000

Risk of injuries

Moving parts

−

The furnace closes automatically. Hands in the area of the opening can

get crushed when the furnace closes.

•

Never reach into the closing furnace.

•

Uses crucible tongs when positioning ceramic crucibles.

CAUTION

C5.0092

Machine falling down

Incorrect installation or insufficient working space

– Due to its weight, the machine can cause injuries if it falls down.
•

Only operate the machine in a sufficiently large, robust, non-slip and
stable working area.

•

Ensure that all machine bases are placed securely on the surface.

CAUTION

C6.0000

Risk of cuts

Glass splinters

−

Sample vials and reagent tubes are made of glass and can break. Glass

splinters can cause cuts.

•

Inspect reagent tubes and sample vials for damage prior to use.

•

Wear protective gloves and goggles when handling reagent tubes
and sample vials.

•

Replace damaged reagent tubes and sample vials.

•

Do not touch glass splinters with unprotected hands.

CAUTION

C7.0000

Risk of burns

Hot machine parts

−

Parts of the machine can get very hot and cause burns during

maintenance work if the waiting time to ensure cooling is not complied
with.

•

Before maintenance work, wait until the temperature of the furnace
is < 40 °C.

•

Check the furnace temperature in the ELEMENTS software.

Содержание ELEMENTRAC CS-i























































































Результаты поиска

Содержание ELEMENTRAC CS-i

Отзывы:

Похожие инструкции для ELEMENTRAC CS-i

Бренды по названию

Популярные бренды

ELTRA ELEMENTRAC CS-i, Руководство по эксплуатации

Результаты поиска

Содержание ELEMENTRAC CS-i

Отзывы:

Похожие инструкции для ELEMENTRAC CS-i

Бренды по названию

Популярные бренды