ELTRA ELEMENTRAC CS-i Скачать руководство пользователя страница 26

Страница: 26 / 86

Operation of the analyzer

WARNING

W15.0017

Risk of injury

Dangerous chemicals

−

Dangerous chemicals can cause fatal poisoning or serious chemical burns

to the skin when working on the machine.

•

Comply with the safety data sheet for the substances used

•

Wear personal protective equipment.

•

Never eat or drink near chemicals0.

WARNING

W16.0000

Risk of poisoning

Toxic combustion gases

−

Samples are exposed to high temperatures during the analysis. Harmful

gaseous fission products can be released or formed from reaction
processes here. These gases can escape from the gas outlet and cause
serious poisoning.

•

Connect the exhaust air outlet on the machine to a suitable
ventilation system.

•

Wear your personal protective equipment.

•

Comply with the safety data sheet for the substances used.

•

Carry out a risk analysis on the potential hazards of your samples
and implement protective measures.

Содержание ELEMENTRAC CS-i























































































Результаты поиска

Содержание ELEMENTRAC CS-i

Отзывы:

Похожие инструкции для ELEMENTRAC CS-i

Бренды по названию

Популярные бренды

ELTRA ELEMENTRAC CS-i, Руководство по эксплуатации

Результаты поиска

Содержание ELEMENTRAC CS-i

Отзывы:

Похожие инструкции для ELEMENTRAC CS-i

Бренды по названию

Популярные бренды