Eltorque QT Series Скачать руководство пользователя страница 46

Страница: 46 / 88

Page

46 of 88

User Manual QT series generation 2.5, ID 2021, rev 3.2, January 14, 2022

Figure 37: Manual operation of the actuator

Figure 38: Position scale

The following subsections describe what triggers an alarm, reactions from
the actuator and how the alarm is reset.

•

Trigger conditions: One or more of the alarms POSITION UNDEFINED,
TEMPERATURE or, TORQUE is active.

•

Reaction from actuator: None for the GENERAL alarm itself, but the other
active alarms that are active have reactions.

•

Reset conditions: The alarms POSITION UNDEFINED, TEMPERATURE and
TORQUE must be inactive.

•

Trigger conditions: The outgoing shaft of the actuator is out of range.

•

Reaction from actuator: None besides an active alarm.

•

Reset conditions: The outgoing shaft must be run back within range.

Valve percent position is a [0%, 100%]

value. A value of 0% corresponds to

the

CLOSED position

, while a value of 100% corresponds to the

OPEN

Содержание QT Series

























































































Результаты поиска

Содержание QT Series

Отзывы:

Похожие инструкции для QT Series

Бренды по названию

Популярные бренды

Eltorque QT Series, Руководство пользователя

Результаты поиска

Содержание QT Series

Отзывы:

Похожие инструкции для QT Series

Бренды по названию

Популярные бренды