ELTEX TAU-4.IP Скачать руководство пользователя

Страница: 174 / 190

174

VoIP Subscriber Gateways

Privilegy

priv

Command mode

CONFIG-NETWORK

Negotiation function 'no' command

Deny the access to the device via HTTP and HTTPS.

Example

tau-8(config-net)# web enable

Port and port profiles settings level commands

username

The command is intended for setting username.

Syntax

username <value>

Parameters

<value> - string: 96 characters

Privilegy

priv

Command mode

CONFIG-VOICE-PORT

Negotiation function 'no' command

Set the default username (default: 00N).

Example

tau-8(config-voice-port)# username 772001

authname

Sets a user name for authentication.

Syntax

authname <value>

Parameters

<value> - string: 96 characters

Privilegy

priv

Command mode

CONFIG-VOICE-PORT

Negotiation function 'no' command

Sets the default user name for authentication (default: 00N).

Example

tau-8(config-voice-port)# authname 772001

Содержание TAU-4.IP































































































































































































Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды

ELTEX TAU-4.IP, Руководство по эксплуатации

Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды