ELTEX TAU-4.IP Скачать руководство пользователя страница 153

Страница: 153 / 190

153

VoIP Subscriber Gateways

network.service0.use_vendor_info=0

network.service0.pppoe_psw_encrypted=7A627F75746F796B

ntp_client.ntp=ntp_client

ntp_client.ntp.enable=0

show version

The command is intended for viewing device configuration version.

Syntax

show version

Parameters

Command contains no arguments.

Privilegy

none

Command mode

EXEC

Example

tau-8> show version

Config version: 8

show configuration

The command is intended for viewing full device configuration.

Syntax

show configuration

Parameters

Command contains no arguments.

Privilegy

priv

Command mode

EXEC

Example

tau-8# show configuration

network.common_settings=common_settings

network.common_settings.1stdns=192.168.0.1

network.common_settings.run_localdns=1

network.common_settings.run_igmpproxy=0

network.common_settings.network_mode=advanced

network.common_settings.wan_speedduplex=Auto

| Press any key to continue | Press 'q' to exit |

show voiceport status

The command is intended for viewing FXS port status.

Содержание TAU-4.IP































































































































































































Результаты поиска

Содержание TAU-4.IP

Отзывы:

ELTEX TAU-4.IP, Руководство по эксплуатации, Страница: 153 / 190

Результаты поиска

Содержание TAU-4.IP

Отзывы: