ELTEX TAU-4.IP Скачать руководство пользователя

Страница: 17 / 190

VoIP Subscriber Gateways

The following connectors and controls are located on the back panel (Table 4).

Table 4 – Description of the connectors and controls on the back panel

Rear panel element

Description

Connector for Wi-Fi-antennas connection

On/Off

ON/OFF switch

12V

Power adapter connector

USB

USB connector for external memory connection

Phone

8×RJ-11 connectors for analogue phone connection

WAN

10/100BASE-T port, 100BASE-TX (RJ-45 connector) for connection
to external network (WAN)

a functional key to reboot the device and reset it to factory settings

1.7

Light indication

Wi-Fi

WAN, Phone

and

Power

LEDs display current state of the device located on the front

panel.

Status list of indicators is shown in Table 5 and 6.

Table 5 – Light indication of the device

LED

LED state

Device state

Wi-Fi

solid green

Wi-Fi network is active

flashes

transmitting data via Wi-Fi

WAN

solid green (10 Mbps)or orange (100
Mbps)

connection between station terminal and
subscriber device is established

flashes

packet data transmission via WAN interface

Phone

solid green

the phone is off-hook

off

phone is on-hook, normal operation

flashes during with 20 Hz frequency
for 1 second, then 4 seconds pause

incoming call is on the phone port

green, flashes slowly in periods

subscriber port registration is absent at SIP-
proxy server

Power

solid green

power is on, normal operation

flashes green

reset the device to the factory settings

orange

internet is not accessible

red

device starts up

_______________________________________

For TAU-8.IP-W only

Содержание TAU-4.IP































































































































































































Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды

ELTEX TAU-4.IP, Руководство по эксплуатации

Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды