ELTEX TAU-4.IP Скачать руководство пользователя

Страница: 40 / 190

VoIP Subscriber Gateways

When ‘

Add VLAN for VoIP

’ flag is set, VoIP services will be made available via

‘VoIP’ service.

the checkbox is disabled, VoIP services will be made available via

‘Internet’

service.

When

‘Add VLAN for Management’

is set, configuring by using DHCP and TR-069 protocol will be

available through

‘Management’ service.

If the checkbox is disabled, configuring by using DHCP and

TR-069 protocol will be available through

‘Internet’

Description of fields (accessible to configure) are described in the section 2.2.1 The ‘Network

settings’ submenu.

To store changes to the operative memory of the device, click the

Save Changes button.

To store

settings into the non-volatile memory, click

Apply

button.

Содержание TAU-4.IP































































































































































































Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды

ELTEX TAU-4.IP, Руководство по эксплуатации

Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды