ELTEX TAU-4.IP Скачать руководство пользователя

Страница: 114 / 190

114

VoIP Subscriber Gateways

VoIP:

VoIP trace enable

– when checked, VoIP trace is enabled otherwise VoIP trace is

disabled. Set the following flags to enter messages with determined type:



Errors;



Warnings;



Debug;



Info;



SIP trace level – from 1 to 9.

IGMP:

IGMP trace enable

– when checked, logging the messages of IGMP protocol is enabled.

When you reboot the device, log file saved in the file system will be lost!

Changes in this menu will be applied immediately after pressing

‘Apply’ button.

Device

reboot is not required.

To store changes to the operative memory of the device, click the

Save Changes

button. To store

settings into the non-volatile memory, click

Apply

button.

3.3.2

The ‘Syslog’ submenu

Use the menu to view the local log file. This service will be available if you select trace in syslogd

and determine name and size of local log file.

Содержание TAU-4.IP































































































































































































Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды

ELTEX TAU-4.IP, Руководство по эксплуатации

Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды