manualshive.com logo in svg

elsner elektronik 71160, Установка и настройка

Поделиться
Скачать
elsner elektronik 71160 Скачать руководство пользователя страница 12

10

Display and operation at the device

KNX eTR 205/206 Light push button

 • Version: 16.12.2020 • Technical changes and errors excepted.

5.

Display and operation at the device

5.1. Adjust room temperature (using the example 

KNX eTR 205 Light)

Depending on the setting of the "Display mode" parameter in the device application,
the 

KNX eTR 205/206 Light push button

 displays the current room temperature

value (or mixed value), the target value or the shift in relation to the basic setpoint. The
display can be dimmed and switched off via the bus so that 

no

 value is displayed.

Option A: Display of actual temperature (room temperature)

The current room temperature is displayed. It is 

not

 possible to change the room

temperature manually using the +/- buttons.

Option B: Display of target temperature or basic setpoint shift

Depending on the setting, the current target value or the shift relative to the base
setpoint is displayed. The temperature can be changed by touching the +/- buttons.

Target value

 display (absolute value):

PRG

Fig. 7
View from bottom

Temperature sensor

Tap +: 
Increase room temperature
(target temperature is
increased)

Tap -: 
Lower room temperature
(target temperature is lowered)

Содержание 71160







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды