Elmo 1/100 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 88

Elmo 1/100 Скачать руководство пользователя страница 7

Gold Twitter Installation Guide

MAN-G-TWI (Ver. 2.000

|Warnings|

www.elmomc.com

7

Table of Contents

Chapter 1:

This Installation Guide

This installation Guide details the technical data, pinouts, and power connectivity of the Gold
Twitter. For a comprehensive detailed description of the functions and connections of the
drive, refer to the Gold Board Level Module Hardware Manual.

Chapter 2:

Safety Information

In order to achieve the optimum, safe operation of the Gold Twitter, it is imperative that you
implement the safety procedures included in this installation guide. This information is
provided to protect you and to keep your work area safe when operating the Gold Twitter and
accompanying equipment.

Please read this chapter carefully before you begin the installation process.

Before you start, ensure that all system components are connected to earth ground. Electrical
safety is provided through a low-resistance earth connection.
Only qualified personnel may install, adjust, maintain and repair the servo drive. A qualified
person has the knowledge and authorization to perform tasks such as transporting,
assembling, installing, commissioning and operating motors.
The Gold Twitter contains electrostatic-sensitive components that can be damaged if handled
incorrectly. To prevent any electrostatic damage, avoid contact with highly insulating
materials, such as plastic film and synthetic fabrics. Place the product on a conductive surface
and ground yourself in order to discharge any possible static electricity build-up.
To avoid any potential hazards that may cause severe personal injury or damage to the
product during operation, keep all covers and cabinet doors shut.
The following safety symbols are used in this and all Elmo Motion Control manuals:

Warning:

This information is needed to avoid a safety hazard, which might cause bodily
injury or death as a result of incorrect operation.

Caution:

This information is necessary to prevent bodily injury, damage to the product
or to other equipment.

Important:

Identifies information that is critical for successful application and
understanding of the product.

«
...
5
6
7
8
9
...
»

Содержание 1/100

























































































Отзывы:

Нет отзывов