Elmdene Quartz-1000-G3 Скачать руководство пользователя страница 10

Страница: 10 / 10

Technical Support Line +44 (0)23 9269 6638 (Option 3)

PAK200544 Iss 01A Mar 2012

PECIFICATION

Sounder Volume

105dB(A) single piezo (QUARTZ-1000-G3)

108 dB(A) dual piezo (QUARTZ-3000-G3)

Cut off Timer

15 minutes max (5 second test)

Waterproofing

All electronics conformal coated

Operating Temp

-25 to + 60 °C

Storage Temp

-25 to + 70 °C

Supply Voltage

9—15V d.c. (13.8 V d.c. nominal)

Current

16 mA max. Quiescent

160 mA max. Sounder (QTZ-1000-G3)
190 mA max. Sounder (QTZ-3000-G3)

40 mA max. Strobe

Battery

Type

Ni-MH

Voltage

6.0V

Capacity

320 mAH

Strobe

Flash Rate

1 Hz reduces to 1/2 Hz after 15 minutes

Comfort LEDs

Alternate flash, 85 per minute

Material

3mm Polycarbonate—all parts

Tamper Detection

Cover and Rear

Kinetic Protection

IK08

OMPLIANCE

This product meets the essential requirements of the following EU Directives:

EMC:

2004/108/EC

RoHS:

2002/95/EC

WEEE:

2002/96/EC

Battery:

2006/66/EC

EN50131-4:2009

Security Grade 3

Environmental Class IV

This product is suitable for use in systems designed to comply with PD6662:2010 at:

Grade 3 and Environmental Class IV.

The packaging supplied with this product may be recycled.

Please dispose of packaging accordingly.

Содержание Quartz-1000-G3











Результаты поиска

Содержание Quartz-1000-G3

Отзывы:

Похожие инструкции для Quartz-1000-G3

Бренды по названию

Популярные бренды

Elmdene Quartz-1000-G3, Руководство пользователя

Результаты поиска

Содержание Quartz-1000-G3

Отзывы:

Похожие инструкции для Quartz-1000-G3

Бренды по названию

Популярные бренды