ELETTROQUADRI MP3 Скачать руководство пользователя страница 50

Страница: 50 / 66

board functions and layout

© ELETTROQUADRI S.r.l.

50 / 66

INSTALLATION MANUAL

6.3.

Insulation test

IMPORTANT

During electrical insulation test all sockets must be removed from MP3 microprocessor board.

Further informations on the procedure are stated on the control panel specific wiring diagram.

6.4.

Safety chain status check points

The MP3 board checks the safety chain status through 4 pick-up points identified by 4 LEDs on REMP2:

Pick-up no.

LED on REMP2

Conn. / term. Controller contacts

J7 / 4

•

Car top stop button

•

Car stop

•

Pit stop

•

Car safety gear

•

Car speed governor

•

Car speed governor tensioner

•

Counterweight speed governor

•

Counterweight speed governor tensioner

•

Pit buffers

•

Car top emergency trap

J7 / 6

•

Limit switch (overtravel)

J7 / 8

•

Manual car door

•

Auxiliary manual swing landing doors

J7 / 10

•

Automatic car door (gate)

•

Automatic landing door locks (without retiring cam).

IMPORTANT

With retiring cam installed, the lock’s switches of manual and automatic landing doors must be

wired after the 4st pick-up point (D4).

6.5.

Switch functions

6.5.1.

UM/DM reed contacts

With only two contacts (UM / DM), in combination with four magnetic strips per floor, the following functions

are available:

•

Floor count (UM for up and DM for down travel)

•

Start of slowdown (stop for 1 speed systems)

•

Stop (both UM and DM are present)

•

Doors zone (both UM and DM are present)

It is possible to cross the slowdown strips if the slowdown distance is greater than half the floor spacing.

ELETTROQUADRI

SINCE 1983

MP3

Содержание MP3



































































Результаты поиска

Содержание MP3

Отзывы:

Похожие инструкции для MP3

Бренды по названию

Популярные бренды

ELETTROQUADRI MP3, Руководство по установке

Результаты поиска

Содержание MP3

Отзывы:

Похожие инструкции для MP3

Бренды по названию

Популярные бренды