ELETTROQUADRI MP3 Скачать руководство пользователя страница 47

Страница: 47 / 66

Diagnostics

© ELETTROQUADRI S.r.l.

47 / 66

INSTALLATION MANUAL

Er – 87

Jumper on the landing door locks

Not

recoverable

The board verifies the presence of input J7/10 (D4).

Verify:

•

Landing door lock contacts.

Er – 88

The bypass relay does not excite (RSVC)

Not

recoverable

The board verifies the presence of input J11/2 (UD).

Verify:

•

Operation of the RSVC relay.

Er – 89

Presence of car door auxiliary contact

Not

recoverable

The MPCAB board verifies the presence of input J21/3 CF1 and J21/4 (CF2).

Er – A0

Speed threshold error with MP-ENC board

Not

recoverable

The set speed threshold has been exceeded.

Verify:

•

The set speed threshold.

•

Slowdown spaces.

Er – A1

Brake opening error with MP-ENC board

Not

recoverable

The MP-ENC board verifies the brake's failure to open.

Verify:

•

Brake contact.

Er – A2

CRS error with MP-ENC board

Not

recoverable

The MP-ENC board detects a speed in excess of the speed setting.

Verify:

•

The set speed threshold.

•

Slowdown spaces.

Er – A3

CRD error with MP-ENC board

Not

recoverable

The MP-ENC board detects a speed in excess of the speed setting.

Verify:

•

The set speed threshold.

•

Slowdown spaces.

Er – A4

CRS1 error with MP-ENC board

Not recoverable

Er – A5

CRD1 error with MP-ENC board

Not recoverable

Er – A6

CRS2 error with MP-ENC board

Not recoverable

ELETTROQUADRI

SINCE 1983

MP3

Содержание MP3



































































Результаты поиска

Содержание MP3

Отзывы:

Похожие инструкции для MP3

Бренды по названию

Популярные бренды

ELETTROQUADRI MP3, Руководство по установке

Результаты поиска

Содержание MP3

Отзывы:

Похожие инструкции для MP3

Бренды по названию

Популярные бренды